Home-Knowledge-

Content

St14 (DC04+ZE) Electrolytic Galvanized Cold-Rolled Steel: Properties and Specification

Feb 19, 2024

What St14 Electrolytic Galvanized Steel Is

St14 is the traditional DIN designation for a cold-rolled deep-drawing steel. In the current European designation system it is written DC04+ZE, material number 1.0338, and is delivered to EN 10152, which covers electrolytically galvanized cold-rolled flat products for cold forming. The strip is produced on a cold-rolling finishing line and then zinc-coated by electrodeposition, which deposits a thin, uniform, and very smooth zinc layer on both surfaces. Because the coating is applied electrolytically rather than by hot dipping, the surface stays bright and even, which makes the product suitable for visible panels, precision stampings, and parts that will be painted.

Designation of the Steel Grade

In EN 10152 the base steel uses the same designations as EN 10130. DC means flat product for cold forming, and the two-digit number indicates the forming capability, with higher numbers giving better deep-drawing performance. The letter combination +ZE identifies the electrolytic zinc coating. Thus DC04+ZE is a deep-drawing grade with an electroplated zinc layer. The old name St14 is still widely used in trading documents, and the two designations refer to the same product family: St14 corresponds to DC04 (1.0338).

Chemical Composition

DC04 (St14) is a low-carbon aluminium-killed steel. The maximum values in EN 10152 are:

Element C Mn P S
Maximum, % 0.08 0.40 0.03 0.03

The low carbon content and the aluminium addition give the steel its deep-drawing ability: the material is soft, with high elongation and a high plastic strain ratio, so it can be drawn into complex shapes without necking or fracture. Unless otherwise agreed at the time of ordering, DC01+ZE, DC03+ZE, DC04+ZE, and DC05+ZE may be supplied as micro-alloyed steel containing additions such as boron or titanium.

Mechanical Properties

Mechanical properties are verified on the coated product by tensile testing in the transverse direction. For DC04+ZE the typical requirements are a yield strength in the range of 140 to 210 MPa, a tensile strength of 270 to 350 MPa, and a minimum elongation of 38% measured on an A80 gauge length for thicknesses above 0.7 mm. When the yield phenomenon is not clearly defined, the 0.2% proof strength Rp0.2 is used instead of the lower yield strength ReL. Two thickness adjustments apply: for 0.5 mm < t <= 0.7 mm the yield strength requirement is raised by 20 MPa and the elongation reduced by 2%; for t <= 0.5 mm the yield strength is raised by 40 MPa and the elongation reduced by 4%. The r90 and n90 values, which characterise drawability, are specified only for thicknesses of 0.5 mm and above, and the r90 requirement is reduced by 0.2 when the thickness exceeds 2 mm.

Electroplated Zinc Coating Grades

EN 10152 defines coating grades by the nominal coating mass per surface, measured as the thickness and mass of zinc on one side. The table below gives the nominal and minimum values for each surface.

Coating grade Nominal thickness per surface, µm Nominal mass per surface, g/m2 Minimum thickness, µm Minimum mass, g/m2
ZE25/25 2.5 18 1.7 12
ZE50/50 5.0 36 4.1 29
ZE75/75 7.5 54 6.6 47
ZE100/100 10.0 72 9.1 65

For reference, a coating mass of 50 g/m2 corresponds to a coating thickness of approximately 7.1 µm. Because the zinc layer is thin compared with hot-dip coatings, electrolytic zinc is chosen for its surface quality and formability rather than for maximum corrosion life; parts made from ZE material are usually painted or used indoors.

Surface Treatments and Quality Classes

EN 10152 divides surface quality into Class A and Class B. Class A is intended for visible, highly finished parts; Class B allows minor surface imperfections. After coating, the strip can receive supplementary surface treatments identified by letter symbols: P is phosphating, C is passivation, O is oiling, PC is phosphating plus chemical treatment, PCO is phosphating, chemical treatment, and oiling, and CO is passivation and oiling. Phosphating improves paint adhesion, passivation slows the formation of white rust during storage, and oiling gives temporary protection during transport. The treatment is always agreed between buyer and mill.

How to Order

A complete order should state the standard, the base grade, the coating grade, the surface quality, and the treatment. An example following the EN 10152 convention is: strip EN 10152 DC04+ZE50/50-A-P, meaning DC04 base steel, ZE50/50 coating, Class A surface, phosphated. The thickness, width, coil or sheet form, and the required documentation complete the specification.

Frequently Asked Questions

Q: What is the difference between St14 and DC04?

St14 is the old German name and DC04 is the current EN designation for the same deep-drawing steel, material number 1.0338. Both terms appear in trade documents and refer to the same base grade.

Q: Is electrolytic galvanizing the same as hot-dip galvanizing?

No. Electrolytic galvanizing deposits zinc by electroplating, giving a very thin, smooth, and uniform layer (typically 2.5 to 10 µm per side). Hot-dip galvanizing immerses the strip in molten zinc and produces a much thicker coating with a spangled surface.

Q: What is St14+ZE used for?

It is used for deep-drawn and stamped parts that need a clean, paintable surface, such as automotive interior components, appliance housings, electrical enclosures, and precision formed parts.

Q: What coating grade should I specify for painted parts?

For painted parts, ZE50/50 with phosphating is a common starting point. The phosphate layer improves paint adhesion, and the zinc layer gives edge protection. Thicker coatings such as ZE75/75 are used where more corrosion resistance is needed.

Q: Does the zinc coating affect deep-drawing performance?

The coating is thin and ductile and does not reduce the forming capability of the base steel. It also acts as a solid lubricant, which can slightly improve drawing behaviour and reduce die wear.

Q: What thickness range is available for DC04+ZE?

EN 10152 covers coated strip from 0.35 mm to 3.0 mm for widths of 600 mm and above, supplied as coil, sheet, or cut lengths.

SEND INQUIRY

SEND INQUIRY