What Does the Designation DX53D Mean?
In the EN 10346 designation system, the first letter D marks a steel product intended for forming (drawing). The letter X indicates that the steel has no specified strength requirement, which allows maximum ductility. The number 53 places the grade in the deep-drawing category: DX53D is more formable than DX51D and DX52D. The final letter D means the product is continuously hot-dip coated, normally with a zinc coating designated +Z. The grade is used when a part must be drawn deeply and still keep a protective zinc layer after forming.
Steel Numbers 1.0355 and 1.0952
European steel documentation uses material numbers alongside grade names. The number 1.0355 is associated with the DX53D substrate in EN 10346, while 1.0952 appears in some delivery documentation for the galvanized condition of the product. The exact assignment can vary with the standard edition, so the grade name and coating designation (for example DX53D+Z275) remain the primary reference on the order and the mill certificate. When a document shows a material number, it should always be checked against the grade name and the coating designation to avoid confusion between substrate and coated product.
Mechanical Properties
The mechanical requirements below apply to DX53D+Z in the delivered condition under EN 10346.
| Property | Value |
|---|---|
| Yield strength Rp0.2 (MPa) | 140 - 260 |
| Tensile strength Rm (MPa) | 270 - 380 |
| Minimum elongation A80 (%), t = 0.35 - 3.0 mm | 26 |
The low yield strength and the moderate tensile range give DX53D the ductility needed for deep drawing and stretch forming, while the consistent cold-rolled surface supports good paint and coating results.
Forming Performance
| Forming Property | Performance |
|---|---|
| Deep drawing | Excellent |
| Bending | Very good |
| Stretch forming | Excellent |
| Surface quality | High |
The microstructure of the low-carbon substrate allows large plastic deformation without fracture, which makes the grade suitable for demanding applications such as automotive body parts, deep-drawn enclosures, and components for white goods.
Coating Options
DX53D galvanized sheet is available with several zinc coating designations. Heavier coatings give longer outdoor life; lighter coatings bend and form more easily and are commonly used for painted interior parts.
| Coating | Minimum total mass both surfaces (g/m²) | Guidance thickness per surface (µm) |
|---|---|---|
| Z100 | 100 | 7 |
| Z140 | 140 | 10 |
| Z180 | 180 | 13 |
| Z200 | 200 | 14 |
| Z225 | 225 | 16 |
| Z275 | 275 | 20 |
| Z350 | 350 | 25 |
| Z450 | 450 | 32 |
The coating mass is measured as the triple-spot average on both surfaces, following EN 10346. Coating adhesion is verified by the bend test required by the standard, so the coating remains intact through the normal forming operations of the grade.
Applications
DX53D+Z is preferred when surface quality is critical, deep forming is required, a long service life is needed, and consistent welding and painting performance is essential. Typical parts include automotive structural and body panels, drawn enclosures, household appliance components, and formed parts for construction equipment. For corrosive outdoor service, heavier coatings such as Z275 or Z350 are selected; for painted interior parts, lighter coatings are normally sufficient.
FAQ
What is the difference between DX51D and DX53D?
DX51D is a general forming grade with no guaranteed yield strength range in the same way, while DX53D is a deep-drawing grade with lower yield strength (140 - 260 MPa) and higher minimum elongation. DX53D is chosen when the part must be drawn more deeply without cracking.
Is 1.0355 the same as DX53D?
1.0355 is the material number commonly assigned to the DX53D base steel in European standards. It describes the substrate; the final product is ordered by the full designation such as DX53D+Z275, which also fixes the coating.
What does 1.0952 refer to?
1.0952 is a material number that appears in some documentation for the coated condition of the grade. Because assignments can differ between standard editions, the grade name and coating designation on the certificate are the reliable reference.
Can DX53D galvanized sheet be welded?
Yes. The zinc coating vaporizes locally at the weld and produces zinc fume, so adequate ventilation is needed. Welding on the steel substrate is straightforward, and the coating damaged at the weld can be repaired with a zinc-rich paint.
Which coating should I choose for outdoor use?
For outdoor and industrial exposure, choose a heavier coating such as Z275 or Z350. The service life in a given atmosphere can be estimated from the coating mass using the corrosion data in ISO 9223 and the guidance in EN ISO 14713-1.
Does deep drawing damage the zinc coating?
DX53D is designed so that the zinc coating withstands the forming operations typical of the grade, and EN 10346 requires bend tests to verify coating adhesion. Very tight radii should be checked against the mill test certificate, and the coating can be repaired with a zinc-rich system where forming locally stresses it.


