hot-dip galvanized steel
DX53D+Z and DX52D+Z are both hot-dip galvanized steel grades defined by EN 10346, widely used for forming and structural manufacturing.
The "DX" designation refers to drawing quality cold-rolled base steel, while "+Z" indicates a zinc coating applied by continuous hot-dip galvanizing for corrosion protection.
Although these two grades appear similar, their mechanical behavior, forming capability, chemical composition, and application limits differ significantly. Choosing the wrong grade often leads to higher scrap rates, forming defects, or unnecessary material cost. Understanding these differences is essential for procurement engineers and manufacturing managers.

Chemical Composition Comparison
| Grade | C (%) | Mn (%) | P (%) | S (%) | Al (%) |
|---|---|---|---|---|---|
| DX52D | ≤0.10 | ≤0.50 | ≤0.045 | ≤0.030 | ≥0.015 |
| DX53D | ≤0.08 | ≤0.45 | ≤0.030 | ≤0.025 | ≥0.015 |
DX53D's lower carbon and phosphorus content directly improves ductility and surface stability during forming.
Mechanical Property Comparison
| Property | DX52D+Z | DX53D+Z |
|---|---|---|
| Yield Strength (MPa) | ≤220 | 140–220 |
| Tensile Strength (MPa) | 270–380 | 270–350 |
| Elongation (%) | ≥26 | ≥36 |
| r-value (plastic strain ratio) | ≥1.3 | ≥1.6 |
| n-value (work hardening) | ≥0.17 | ≥0.20 |
DX53D+Z provides significantly higher elongation and formability, making it suitable for deep drawing and complex geometries.
Specification Range (Both Grades)
| Thickness (mm) | Width (mm) | Length (mm) | Zinc Coating |
|---|---|---|---|
| 0.30 – 3.00 | 600 – 1500 | 1000 – 6000 | Z60 – Z275 |
Forming Performance Differences
DX52D+Z is ideal for moderate forming, such as bending, shallow stamping, and general sheet metal work.
DX53D+Z is specifically engineered for deep drawing, multiple forming stages, and high-strain deformation with minimal risk of tearing or surface damage.
Application Comparison
| Application | DX52D+Z | DX53D+Z |
|---|---|---|
| HVAC ducts | ✔️ | ✔️ |
| Appliance housings | ✔️ | ✔️ |
| Automotive inner panels | ⚠️ | ✔️ |
| Complex stamped parts | ⚠️ | ✔️ |
| Electrical enclosures | ✔️ | ✔️ |
| Deep-drawn components | ❌ | ✔️ |
GNEE STEEL maintains strict process control on base metal chemistry, annealing cycles, coating thickness, and surface finish. This ensures both DX52D+Z and DX53D+Z meet consistent forming and corrosion performance across large export orders.
Alongside DX52D+Z and DX53D+Z, GNEE STEEL supplies DX51D+Z, DX54D+Z, Galvalume steel, PPGI, cold rolled coils, and hot rolled steel plates, providing complete steel sourcing support for global manufacturers.
|
Standard |
Grade |
C |
Si |
Mn |
P |
S |
Ti |
|
Forcold Forming Chinese Standard |
DX51D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
DX52D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX53D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX54D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX56D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX57D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
Forcold Forming Japanese Standard |
SGCC |
0.15 |
0.50 |
0.80 |
0.050 |
0.030 |
0.025 |
|
SGCD1 |
0.12 |
0.50 |
0.60 |
0.040 |
0.030 |
0.025 |
|
|
SGCD3 |
0.08 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
SGCD4 |
0.06 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
For Structure Japanese Standard |
SGC340 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.025 |
|
SGC400 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.150 |
|
|
SGC490 |
0.30 |
0.50 |
2.00 |
0.200 |
0.035 |
0.025 |
|
|
SGC510 |
0.30 |
0.50 |
2.50 |
0.200 |
0.035 |
0.025 |
|
|
For Structure AISI Standard |
S220GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
S250GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S280GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S320GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S350GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |
|
|
S550GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |


