hot-dip galvanized steel
DX53D+Z and DX52D+Z are both hot-dip galvanized steel grades defined by EN 10346, widely used for forming and structural manufacturing.
The "DX" designation refers to drawing quality cold-rolled base steel, while "+Z" indicates a zinc coating applied by continuous hot-dip galvanizing for corrosion protection.
Although these two grades appear similar, their mechanical behavior, forming capability, chemical composition, and application limits differ significantly. Choosing the wrong grade often leads to higher scrap rates, forming defects, or unnecessary material cost.

Mechanical Capability Overview
| Parameter | DX52D+Z | DX53D+Z |
|---|---|---|
| Yield Strength | ≤220 MPa | 140–220 MPa |
| Elongation | ≥26% | ≥36% |
| r-value | ≥1.3 | ≥1.6 |
| Typical Forming Level | Moderate | Deep drawing |
| Scrap Rate Risk | Medium | Low |
Zinc Coating Options for Both Grades
| Coating Type | Coating Weight (g/m²) | Typical Use |
|---|---|---|
| Z60 | 60 | Indoor equipment |
| Z100 | 100 | Light outdoor |
| Z180 | 180 | Industrial |
| Z275 | 275 | Marine, infrastructure |
Cost-Performance Consideration
DX52D+Z is more economical for simple parts and moderate forming.
DX53D+Z slightly increases material cost but dramatically reduces scrap, tooling wear, and rework costs in complex forming projects - often delivering a lower total manufacturing cost.
Project Selection Guide
| Manufacturing Requirement | Recommended Grade |
|---|---|
| Simple bending | DX52D+Z |
| Shallow stamping | DX52D+Z |
| Multi-stage forming | DX53D+Z |
| Deep cavities & housings | DX53D+Z |
| High cosmetic surface | DX53D+Z |
| Long-term corrosion exposure | Both (with proper coating) |
GNEE STEEL supports customers with grade selection, coating optimization, forming analysis, and full technical documentation to ensure every project achieves the best balance of performance, durability, and cost efficiency.
In addition to DX52D+Z and DX53D+Z, GNEE STEEL supplies a full range of galvanized and coated steel solutions including DX51D–DX54D, Galvalume steel, pre-painted steel, cold rolled coils, and structural hot rolled plates - enabling customers to consolidate sourcing with a reliable long-term partner.
|
Standard |
Grade |
C |
Si |
Mn |
P |
S |
Ti |
|
Forcold Forming Chinese Standard |
DX51D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
DX52D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX53D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX54D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX56D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX57D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
Forcold Forming Japanese Standard |
SGCC |
0.15 |
0.50 |
0.80 |
0.050 |
0.030 |
0.025 |
|
SGCD1 |
0.12 |
0.50 |
0.60 |
0.040 |
0.030 |
0.025 |
|
|
SGCD3 |
0.08 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
SGCD4 |
0.06 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
For Structure Japanese Standard |
SGC340 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.025 |
|
SGC400 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.150 |
|
|
SGC490 |
0.30 |
0.50 |
2.00 |
0.200 |
0.035 |
0.025 |
|
|
SGC510 |
0.30 |
0.50 |
2.50 |
0.200 |
0.035 |
0.025 |
|
|
For Structure AISI Standard |
S220GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
S250GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S280GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S320GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S350GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |
|
|
S550GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |


