Home-Knowledge-

Content

Hot-Dip Galvanized Sheet: Why Skin-Pass Leveling Matters

Aug 18, 2025

1. What "Finishing" Means on a Galvanizing Line

On a continuous hot-dip galvanizing line, finishing usually refers to the skin-pass (temper rolling) operation performed after the strip leaves the zinc bath and cools. A light cold reduction - typically 0.5–2% - is applied through specially prepared work rolls. Far from being a cosmetic step, skin-pass leveling determines the sheet's flatness, surface topography and mechanical response in the customer's press shop. It is the difference between a coil that forms cleanly and one that produces stretcher strain lines on the panel surface.

2. Why Leveling Matters: Four Technical Benefits

Flatness and surface evenness: Leveling flattens thin sheets and presses down surface zinc particles, giving a smoother finish that is especially valuable for deep drawing and high-precision applications.

Controlled surface roughness: Pre-blasted leveling rolls imprint a defined roughness profile. This improves coating adhesion and stores lubricant on the surface, improving die lubrication during deep drawing.

Uniform appearance: For painted galvanized sheet with minimized spangle, small spangles can still show through thin paint films. Leveling produces the uniform silver-white appearance required for high-end visible products.

Better formability: Leveling lowers the lower yield point and eliminates or masks the yield plateau, preventing stretcher strain (Lüders) lines during stretching and deep drawing.

3. Steel Grades Commonly Galvanized

Hot-dip galvanized sheet is produced from several substrate families, each answering a different forming requirement. Commercial Quality (CQ) grades such as DX51D per EN 10346 and SGCC per JIS G3302 cover general bending and simple forming. Deep Drawing Quality (DDQ) grades such as DX53D/DX54D handle complex pressings. High-Strength Low-Alloy (HSLA) grades such as S220GD–S550GD deliver structural strength with a zinc coating. Bake Hardened (BH), Dual Phase (DP) and TRIP steels extend the range into automotive applications where paint-baking increases yield strength or crash-energy absorption is required.

4. Process Families and Corrosion Testing

Hot-dip galvanizing is classified by annealing route: in-line annealing (protective-gas or Sendzimir-type process) and off-line annealing (flux process). Furnace configurations include vertical, horizontal and vertical-horizontal types. Corrosion resistance of the finished sheet is verified by three complementary methods: the salt spray test, the humidity test and the etching test; coating mass is determined gravimetrically per EN ISO 1460 or ASTM A90, while local thickness can be checked by magnetic gauge per EN ISO 2178.

5. White Rust: Causes and Prevention

Even a perfect zinc coating can develop white rust if the product is exposed to humid air containing acidic pollutants such as SO₂, CO₂ and NOₓ. White rust consists mainly of ZnO and Zn(OH)₂, forms quickly on wet, poorly ventilated surfaces, and not only looks bad - it consumes the sacrificial coating and complicates subsequent painting. Typical causes include storing coils together with acids, alkalis or salts, damaged passivation film, ineffective passivation or oiling, humid unventilated warehouses, water exposure during transport, and condensation from cold-to-warm temperature changes. Prevention starts at the mill (proper passivation, oiling, dry packaging) and continues in the warehouse: keep coils dry, ventilated and above floor level, and never store them near corrosive media.

Frequently Asked Questions

Why is skin-pass leveling needed if the sheet already looks flat? Because as-galvanized strip can carry residual shape defects and a yield plateau in the stress-strain curve. Leveling removes both: it corrects micro-flatness and eliminates the plateau, so forming does not produce surface stretcher strain lines.

What is the difference between in-line and off-line annealing? In-line annealing (protective-gas method) anneals and galvanizes in one continuous pass; off-line annealing (flux method) anneals the strip first, then galvanizes it in a separate stage. The choice affects surface quality, throughput and product mix.

How is the zinc coating weight measured? By the gravimetric method per EN ISO 1460 / ASTM A90: a weighed specimen is stripped in inhibited acid, reweighed, and the mass difference is reported in g/m² (total, both sides). Magnetic gauges per EN ISO 2178 give local thickness on finished parts.

Which steel grade should I choose for deep drawing? For complex draw ratios use DDQ grades such as DX53D/DX54D (EN 10346) or SGCD1–SGCD3 (JIS G3302). If the part only needs simple bending, a CQ grade like DX51D/SGCC is more economical.

Can white rust be avoided completely? With effective passivation, oiling and dry ventilated storage it can be minimized to a barely visible level. If white rust appears, light forms can often be cleaned and passivated again; heavy attack consumes coating thickness and should be checked by coating-weight measurement.

Does leveling change the mechanical properties of the steel? Leveling slightly increases yield strength and removes the discontinuous yield point. It does not change tensile strength or elongation significantly, and the effect is precisely what improves press-shop performance.

SEND INQUIRY

SEND INQUIRY