1. What Is DX53D Steel?
2. Chemical Composition
EN 10346 specifies maximum values for the chemical composition of the DX51D-DX57D family, and DX53D is covered by the same table. The typical maximum limits are: carbon 0.12%, silicon 0.50%, manganese 0.60%, phosphorus 0.10%, sulfur 0.045% and titanium 0.30%. These generous maxima allow mills flexibility; actual values are confirmed on the mill test certificate and are usually well below the limits. Note that the zinc coating is not part of the base steel chemistry - its mass is specified separately by the coating designation (for example +Z200 means about 200 g/m² total zinc on both surfaces).
| Element (max %) | C | Si | Mn | P | S | Ti |
|---|---|---|---|---|---|---|
| DX53D+Z (EN 10346 family limits) | 0.12 | 0.50 | 0.60 | 0.10 | 0.045 | 0.30 |
3. Mechanical Properties
Under EN 10346, DX53D is required to meet: yield strength (Rp0.2) 140-300 MPa, tensile strength (Rm) 270-420 MPa, and minimum elongation (A80) of 30% for the common thickness range. The material also shows good work-hardening behavior: the strain-hardening exponent (n-value) and plastic strain ratio (r-value) support deep drawing and stretching without necking or tearing. In practice this means DX53D coils can be stamped, deep-drawn and roll-formed into parts with compound curves, and the forming behavior stays consistent coil to coil when supplied by a mill with controlled processing.
| Property (EN 10346 range) | DX53D+Z |
|---|---|
| Yield strength Rp0.2 | 140-300 MPa |
| Tensile strength Rm | 270-420 MPa |
| Elongation A80 (min) | 30% |
4. Applications of DX53D Steel
| Industry | Typical Parts |
|---|---|
| Automotive | Body panels, door frames, seat parts, bumper reinforcements, fuel tank shields, underbody components |
| Home appliances | Washing machine drums and wrappers, refrigerator doors and liners, oven housings, microwave panels, dishwasher parts |
| Construction | Roofing profiles, wall cladding, ventilation ducts, light structural sections, facade elements |
| Furniture | Filing cabinets, metal storage units, shelving, desk and bed frames |
| Electrical equipment | Transformer enclosures, electrical cabinet housings, mounting plates, generator covers, switchgear panels |
| HVAC | Air ducts, heat exchanger casings, ventilation covers, air-conditioning housings |
| Agriculture | Machinery housings, protective covers, storage bins, equipment panels |
5. Comparing DX53D with DX51D, DX52D and DX54D
6. Procurement Guidance
Frequently Asked Questions
Q: What does the 53 mean in DX53D?
A: It is the formability index within the EN 10346 cold-forming family. Higher numbers (DX54D-DX57D) indicate progressively better deep-drawing capability; DX53D sits in the deep drawing range, above the DX51D/DX52D general and drawing grades.
Q: Is DX53D the same as SGCD2 or SGCD3?
A: Not identical, but comparable. SGCD2/SGCD3 are JIS G 3302 drawing grades with broadly similar formability levels; DX53D is the EN 10346 designation. They are not automatically interchangeable, so specify to the standard your contract requires.
Q: What is the difference between DX53D and DX53D+Z?
A: DX53D is the base-grade family name; the +Z suffix specifies the actual metallic coating (hot-dip zinc). You cannot order bare DX53D as a coated product; the coating designation must always be stated, for example DX53D+Z200.
Q: Can DX53D be welded?
A: Yes, with standard methods for coated steel (spot, MIG/MAG, TIG). Zinc-coated surfaces may need local coating repair at welds to restore corrosion protection, and adequate fume extraction is required when welding coated steel.
Q: What is the old designation of DX53D?
A: It was formerly designated FeP05G in the earlier European standard system; the material number is 1.0951. Modern orders should use the EN 10346 designation.
Q: How do I verify the coating mass of DX53D+Z I receive?
A: Weigh a sample before and after stripping the coating (or use a magnetic gauge for thickness), and compare with the coating designation on the mill certificate. Third-party inspection can perform the same checks and issue a report before shipment.


