hot-dip galvanized steel S350GD
The hot-dip galvanized steel S350GD in accordance with the EN 10346 standard is a high-strength structural steel that has been specifically developed for demanding applications in structural engineering and building construction. With the material number 1.0529, the minimum yield strength Rp0.2 is 350 N/mm², placing S350GD in the upper strength classes of hot-dip galvanized structural steels. Hot-dip galvanizing ensures a homogeneous zinc coating on the surface, which protects the steel against corrosion in the long term. Thanks to six different coating variants – +Z, +ZF, +ZA, +ZM, +AZ and +AS – the material can be optimally adapted to the specific environmental and stress conditions.
S350GD+Z hot dip galvanized plates(coils) are featured with strong coating adhesiveness, high erosion-resistance, accurately controlled zinc coating thickness, high size precision, flat profile and good mechanical, processing and welding performance. They can be used for making outside and inside automotive plates, structural parts and reinforcements.

S350GD+Z hot dip galvanized coils
S350GD+Z hot dip galvanized automotive steel size:
Nominal thickness: 0.30mm~3.0mm, nominal width: 800mm~1830mm
Note: nominal thickness of a plate/strip is sum of base plate thickness and coating thickness.
S350GD+Z hot dip galvanized automotive steel mechanical performances and coating adhesiveness:
|
Steel grade |
Mechanical performances |
Coating adhesiveness |
|||
|
Yield strength MPa ≥ |
Tensile strength MPa ≥ |
After breakage percent elongation % ≥ |
Bending center diameter ( a=plate thickness) |
||
|
L0=80mm, b=20mm |
|||||
|
Nominal thickness mm |
|||||
|
≤0.7 |
>0.7 |
||||
|
S350GD+Z(StE345-2Z) |
350 |
420 |
14 |
16 |
3a |
a.bending center diameter is 4a in case of nominal thickness>1.5mm.
S350GD+Z hot dip galvanized automotive steel coating weight range:
|
|
Applicable surface structure |
Weight range of following coatings a g/m²(A/B) |
|
|
Zinc coating |
Zn-Fe alloy coating |
||
|
Equally coating |
Z, X, G, GX, N, R |
40/40~225/225 |
30/30~90/90 |
|
Differential coating b |
N, R |
30~150(each side) |
- |
|
a. 50 g/m² coating weight is equivalent to about 7.1 µm. |
|||
S350GD+Z hot dip galvanized automotive steel surface treatment:
1 Chromate treatment (L) |
Chromate treatment is a treatment with an aim to prevent white rusts formed on product surfaces during transportation and storage. |
|
2 Oiling (Y) |
Oiling is to prevent white rusts formed on product surfaces during transportation and storage. |
|
3 Chromate treatment + oiling (LY) |
This treatment with oiling after surface chromate treatment is to further avoid the forming of white rusts. |
S350GD+Z hot dip galvanized automotive steel surface quality:
Code No. |
Features |
|
FB(O3) |
It is allowed for the existence of small erosion spots, dark spots, strip marks, minor chromate treatment defects and small zinc particles. |
|
FC(O4) |
No erosion spot is allowed. However, it is allowed for the existence of light impression, scratches, zinc flow ripple marks, minor chromate treatment defects in small range, while the other side must reach FB requirements at least. |
|
FD(O5) |
One side of relatively good quality must further restrict on defects, namely appearance quality after painting is not affected, and the other side must FB requirements at least. |
With the upgrading of global infrastructure demand, the market application scenarios of S350GD galvanized steel continue to expand. We not only provide high-quality materials that meet international standards, but also offer a full-chain solution from material selection to processing. Contact us now and let S350GD galvanized steel be a solid partner for your project's success.
- Available Steel Grade
|
Standard |
Grade |
C |
Si |
Mn |
P |
S |
Ti |
|
Forcold Forming Chinese Standard |
DX51D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
DX52D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX53D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX54D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX56D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX57D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
Forcold Forming Japanese Standard |
SGCC |
0.15 |
0.50 |
0.80 |
0.050 |
0.030 |
0.025 |
|
SGCD1 |
0.12 |
0.50 |
0.60 |
0.040 |
0.030 |
0.025 |
|
|
SGCD3 |
0.08 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
SGCD4 |
0.06 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
For Structure Japanese Standard |
SGC340 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.025 |
|
SGC400 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.150 |
|
|
SGC490 |
0.30 |
0.50 |
2.00 |
0.200 |
0.035 |
0.025 |
|
|
SGC510 |
0.30 |
0.50 |
2.50 |
0.200 |
0.035 |
0.025 |
|
|
For Structure AISI Standard |
S220GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
S250GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S280GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S320GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S350GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |
|
|
S550GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |


