What Cold-Rolled Sheet Is
Cold-rolled steel sheet starts as hot-rolled coil that is pickled to remove the oxide scale, then rolled at ambient temperature to the final thickness. The cold reduction improves the surface and the dimensional accuracy, and the material is then annealed to restore the ductility lost in rolling, and finally skin-passed or temper-rolled to control the surface finish and the flatness. The product is delivered either as coil or as cut sheets. Because the process runs without reheating the steel, the surface is free of the pitting and scale defects typical of hot-rolled products, and the thickness tolerance is tight, which matters for stamping, painting, and roll forming.
SPCC and DC01: The General-Purpose Grades
SPCC is the commercial-quality cold-rolled grade of JIS G3141, and DC01 is the general-forming grade of EN 10130. They are the practical equivalents of the two standard systems and are the most traded cold-rolled grades in the world. Both are low-carbon steels with good cold-bending and welding performance and sufficient ductility for simple stamping. They are the standard substrate for corrugated roofing sheets, for galvanized and colour-coated roofing products, and for general fabrication such as furniture, cabinets, drums, and shelving. Where the part must be deep-drawn, the drawing grades of the same standards, such as SPCD, SPCE, DC03, or DC04, are used instead.
Surface Finish and Protection
Cold-rolled sheet is supplied with a bright or matte surface and in oiled or dry condition. Oiling is the standard protection for shipment and storage: a thin rust-preventive oil is applied at the exit of the temper mill, and it contains corrosion inhibitors that ordinary forming lubricants do not have. The oil is removed by the downstream process, normally by degreasing before painting or plating. For long export shipments, particularly to tropical and coastal destinations, oiled delivery plus moisture-barrier packaging is recommended, because condensation during the voyage is a common cause of surface rust on dry material. Sheets can also be supplied dry for immediate processing where the buyer's line cannot handle oil.
Quality Characteristics
The useful properties of cold-rolled sheet for roofing and general use are its clean surface, its thickness tolerance, and its consistent mechanical properties along the coil and from sheet to sheet. Thickness tolerance classes are defined in the governing standard and should be stated for critical applications. Flatness is important for sheeting lines: the strip must feed smoothly through the roll former, and the sheet must lie flat for cutting and stacking. These characteristics are verified by the mill test certificate, which reports the heat analysis and the mechanical test results for the lot.
Roofing and Construction Applications
In the roofing sector, cold-rolled SPCC or DC01 is used in two ways: as the substrate that is coated on the galvanizing or coil-coating line and then formed into profiled roofing sheets, and as a bare sheet that is cut and formed on site or in the factory before painting. Corrugated roofing sheets, roof tiles, flashings, and ridge components are all produced from this material family. The finished roof performance is set by the coating and the profile, while the base steel carries the structural stiffness. For roof sheets that will remain bare, the cold-rolled product is normally hot-dip galvanized first, per EN 10346 or JIS G3302, because bare cold-rolled sheet corrodes quickly outdoors.
Specification and Ordering
When ordering cold-rolled sheet, specify the standard and edition, the grade, the thickness and width with the tolerance class, the surface finish, the oiling condition, the delivery form (coil or sheet, sheet length), and the documentation. For roofing applications that will be coated or painted, confirm the surface quality class. For export, agree the packaging: coils banded and wrapped with moisture barrier, sheets crated or palletised with edge protection, and the container lined and vented appropriately. A clear specification protects both the buyer and the mill from disputes about surface, tolerance, and packaging at the destination.
Frequently Asked Questions
Q: What is the difference between SPCC and DC01?
SPCC is the general-purpose cold-rolled grade of JIS G3141 and DC01 is the equivalent of EN 10130. They are commonly interchanged in trade after verifying the property and tolerance tables for the ordered thickness.
Q: Can cold-rolled sheet be used directly for roofing?
Bare cold-rolled sheet is not suitable for long-term outdoor roofing because it rusts. It is used as the substrate that is galvanized or colour-coated before forming into roof sheets, or for interior applications.
Q: Why is cold-rolled sheet oiled?
The oil is a rust-preventive that protects the clean surface during transport and storage. It is removed by degreasing before painting, plating, or other surface treatment.
Q: What thickness of cold-rolled sheet is used for roofing profiles?
Roofing profiles are commonly formed from 0.35 to 0.60 mm steel, with thicker material for structural cladding. The base is usually coated, and the total product thickness includes the coating.
Q: How is cold-rolled sheet packaged for export?
Coils are banded and wrapped with a moisture barrier; sheets are palletised or crated with edge protection. The packaging should protect against condensation and handling damage during the voyage.
Q: What standards apply to SPCC and DC01?
SPCC is defined in JIS G3141 and DC01 in EN 10130. Both standards cover cold-reduced low-carbon steel sheet and strip, with their own tolerance and property tables.


