What Is S550GD Galvanized Steel?
S550GD is a continuously hot-dip coated structural steel grade defined in EN 10346:2015. The designation means a minimum yield strength of 550 MPa in the as-delivered condition, with tensile strength typically between 600 and 730 MPa and a minimum elongation of 14% measured on an A80 specimen. The zinc coating, identified by the +Z suffix, provides sacrificial corrosion protection to the steel substrate. These properties make S550GD a common choice for load-bearing sections such as purlins, gantries, solar mounting rails, and industrial racking, where both strength and corrosion resistance are required.
Surface Treatment Types for S550GD Steel
The zinc coating produced on the hot-dip galvanizing line is the primary protection for S550GD. Additional surface treatments are then applied depending on how the material will be stored, transported, formed, or painted. The table below summarises the main treatment types used in practice.
| Treatment | Typical Coating Mass / Layer | Main Purpose | Typical Reference |
|---|---|---|---|
| Hot-dip galvanizing (Z) | Z60 to Z275 (60-275 g/m² per side, triple-spot average) | Sacrificial corrosion protection of the base steel | EN 10346 |
| Passivation (chromate or chromate-free) | Thin conversion layer, typically 0.5-2 µm | Prevents wet-storage stain during transport and storage | EN 10346 / EN ISO 14713 |
| Phosphating | Crystalline phosphate layer | Improves paint adhesion for subsequent coil coating | Industry practice for prepainted substrate |
| Oiling | Light mineral oil film | Temporary protection against white rust in humid storage | Supplier specification |
| Powder coating | 60-120 µm cured powder film | Decorative finish and additional barrier protection | ISO 12944-5 (duplex system) |
How Each Treatment Works
Hot-dip galvanizing immerses the steel strip in a molten zinc bath at roughly 450 °C; the reaction forms intermetallic layers (Gamma, Delta, and Zeta phases) with a pure zinc outer layer, giving the characteristic spangle appearance unless suppressed by zinc-aluminium alloy additions. Passivation applies a chemical conversion layer that slows the formation of white rust when coiled steel is exposed to condensation; chromate-free formulations based on trivalent chromium or organic polymers are now standard in most European supply chains. Phosphating produces a microcrystalline surface that anchors organic paint systems and is normally applied before coil coating or powder coating. Oiling is a temporary measure used when the coil will be stored for several weeks before further processing, and the oil film is removed by the degreasing stage of the customer's paint line.
Selecting a Surface Treatment by Application
| Application | Recommended Treatment | Typical Coating Mass |
|---|---|---|
| Roofing and wall cladding sections | Passivated Z coating, optionally prepainted | Z100-Z275 |
| Solar mounting structures | Passivated Z coating | Z200-Z275 |
| Automotive or appliance stampings | Phosphated or chromate-free treated | Z100-Z180 |
| Long-term outdoor storage prior to use | Oiled or passivated, stored dry | Z140-Z275 |
| Architectural visible surfaces | Powder coated or coil coated over Z substrate | Z180-Z275 |
Quality Control and Testing of Surface Treatments
Verification of the zinc coating is normally carried out by magnetic induction thickness measurement or by gravimetric methods that dissolve the coating and weigh the zinc removed, in accordance with EN 10346. Adhesion is checked by bend tests at a mandrel diameter related to the sheet thickness, and the coating must not flake or detach from the substrate. Corrosion resistance is evaluated with neutral salt spray testing per ASTM B117 or ISO 9227, while wet-storage stain resistance is assessed by a humidity cabinet test. For painted or powder-coated surfaces, cross-cut adhesion, impact resistance, and gloss retention are verified against the coating supplier's specification. A complete mill test certificate, issued in line with EN 10204 type 3.1, records the mechanical properties, chemical composition, and coating mass of each delivered lot.
Benefits of a Correctly Specified Surface Treatment
Specifying the right surface treatment for S550GD delivers measurable benefits. A properly passivated Z275 coating on a 1.5 mm sheet can provide more than 30 years of maintenance-free life in a moderate industrial atmosphere, based on the zinc consumption rates given in ISO 9223 and EN ISO 14713-1. Phosphating reduces paint line defects and improves first-pass adhesion, which lowers the reject rate in coil coating operations. Oiling prevents white rust claims during sea freight and warehousing. In structural applications, a duplex system of galvanizing plus powder coating can extend service life beyond the sum of the two individual systems, which is why it is specified for coastal and chemical-industry structures.
FAQ
What is the difference between S550GD and ordinary structural steel?
S550GD is a hot-dip coated grade with a guaranteed minimum yield strength of 550 MPa, while ordinary structural steel such as S235 or S355 is normally supplied uncoated. The coating adds corrosion protection that plain carbon steel does not have.
Can S550GD be bent after galvanizing?
Yes. EN 10346 specifies bend tests for the coating, and the steel is designed for roll forming and press braking. The minimum elongation of 14% is sufficient for most structural profiles, although tight radii should be verified against the supplier's bend test data.
Is passivation required for S550GD coils?
Passivation is recommended when coils will be stored or shipped in humid conditions, because it suppresses white rust on the zinc surface. It can be omitted if the material will be processed immediately and the customer's process requires a bare zinc surface.
What coating masses are available for S550GD?
Standard coating masses under EN 10346 range from Z60 to Z275. Heavier coatings such as Z350 or Z450 can be produced by agreement, and Z275 is the most common choice for outdoor structural applications.
Does phosphating affect weldability?
Phosphating is applied in very thin layers and does not interfere with spot welding or arc welding in normal fabrication practice. The phosphate layer may be removed locally before welding if the customer's procedure demands it.
How is the zinc coating thickness verified on delivered material?
The common methods are magnetic induction gauging for a quick check on individual sheets and the gravimetric method per EN 10346, which gives the average coating mass of a sample. Mill test certificates record the triple-spot average and the single-spot minimum.


