Home-Knowledge-

Content

S250GD+Z Vs S350GD+Z – Structural Performance, Coating Characteristics, And Application Selection

Jan 07, 2026

hot-dip galvanized structural steel

 

S250GD+Z and S350GD+Z are two commonly specified hot-dip galvanized structural steel grades designed for load-bearing and semi-structural applications. Both grades are produced through continuous hot-dip galvanizing, where a zinc coating (+Z) is metallurgically bonded to the steel surface, providing long-term corrosion protection.

 

The key distinction between these two grades lies in their mechanical strength levels. While S250GD+Z offers balanced strength and formability, S350GD+Z provides higher yield strength for more demanding structural requirements. Understanding their differences is essential for engineers, designers, and procurement specialists seeking to optimize performance, weight, and cost.

 

hot-dip galvanized structural steel grades

Mechanical Property Comparison

 

The yield strength designation directly influences structural capacity and material selection.

Table 1 – Mechanical Properties Comparison

Property S250GD+Z S350GD+Z
Minimum Yield Strength ≥ 250 MPa ≥ 350 MPa
Tensile Strength 300–410 MPa 420–550 MPa
Elongation (%) ≥ 20 ≥ 16
Structural Capacity Medium High
Formability Very Good Good

S250GD+Z is easier to form and bend, making it suitable for components requiring complex shapes. S350GD+Z, with its higher strength, supports greater loads and allows for thinner material in structural designs.

 

Zinc Coating (+Z) and Surface Characteristics

 

Both grades share similar zinc coating options and surface treatments, but application requirements often differ due to strength-related use cases.

Common Zinc Coating Options

Coating Designation Zinc Mass (g/m²) Typical Environment
Z100 100 Indoor, low corrosion
Z140 140 General outdoor
Z180 180 Industrial
Z220 220 Coastal, marine

Higher coating mass is frequently paired with S350GD+Z in harsh environments where structural safety and corrosion resistance are equally critical.

 

Zinc Spangle and Surface Finish Options

 

Both S250GD+Z and S350GD+Z can be supplied with:

  • Regular Spangle (RS): Functional, economical, structural use
  • Minimized Spangle (MS): Cleaner appearance, better paint adhesion
  • Zero Spangle (ZS): Smooth surface for painted or architectural applications

Passivated / Anti-Fingerprint (AFP) surfaces

For high-visibility or painted components, minimized or zero spangle is preferred regardless of grade.

 

Application Scenarios: When to Use Each Grade

 

  • S250GD+Z Typical Applications

Secondary structural framing

Roof purlins and wall girts

Light steel buildings

Agricultural and storage structures

Its superior formability and cost efficiency make it ideal for large-volume projects with moderate load demands.

 

  • S350GD+Z Typical Applications

Primary load-bearing members

High-strength steel structures

Solar mounting systems

Industrial platforms and support frames

The higher yield strength enables reduced material thickness while maintaining safety margins.

 

Table 3 – Typical Supply Range

Grade Thickness (mm) Width (mm) Surface Options
S250GD+Z 0.45–1.50 800–1500 RS / MS / ZS
S350GD+Z 0.50–1.50 900–1500 MS / ZS / AFP

 

Choosing between S250GD+Z and S350GD+Z depends on structural load requirements, fabrication complexity, and lifecycle expectations. S250GD+Z offers excellent versatility and cost efficiency, while S350GD+Z delivers superior strength for demanding structural applications.

 

GNEE STEEL supplies both grades with flexible zinc coating weights, spangle options, and customized dimensions to meet project-specific requirements.

 

📩 Contact GNEE STEEL today to receive technical support and a tailored quotation.

 

Standard

Grade

C

Si

Mn

P

S

Ti

Forcold Forming

Chinese Standard

DX51D+Z

0.12

0.50

0.60

0.100

0.045

0.30

DX52D+Z

0.12

0.50

0.60

0.100

0.045

0.30

DX53D+Z

0.12

0.50

0.60

0.100

0.045

0.30

DX54D+Z

0.12

0.50

0.60

0.100

0.045

0.30

DX56D+Z

0.12

0.50

0.60

0.100

0.045

0.30

DX57D+Z

0.12

0.50

0.60

0.100

0.045

0.30

Forcold Forming

Japanese Standard

SGCC

0.15

0.50

0.80

0.050

0.030

0.025

SGCD1
SGCD2

0.12
0.10

0.50
0.50

0.60
0.45

0.040
0.030

0.030
0.030

0.025
0.025

SGCD3

0.08

0.50

0.45

0.030

0.030

0.025

SGCD4

0.06

0.50

0.45

0.030

0.030

0.025

For Structure

Japanese Standard

SGC340

0.25

0.50

1.70

0.200

0.035

0.025

SGC400
SGC440

0.25
0.25

0.50
0.50

1.70
2.00

0.200
0.200

0.035
0.035

0.150
0.150

SGC490

0.30

0.50

2.00

0.200

0.035

0.025

SGC510

0.30

0.50

2.50

0.200

0.035

0.025

For Structure

AISI Standard

S220GD+Z

0.20

0.60

0.70

0.100

0.045

0.025

S250GD+Z

0.20

0.60

0.70

0.100

0.045

0.025

S280GD+Z

0.20

0.60

0.70

0.100

0.045

0.025

S320GD+Z

0.20

0.60

0.70

0.100

0.045

0.025

S350GD+Z

0.20

0.60

0.70

0.100

0.045

0.150

S550GD+Z

0.20

0.60

0.70

0.100

0.045

0.150

 

Contact now

SEND INQUIRY

SEND INQUIRY