Home-Knowledge-

Content

Instrument Transformer Basics: CT vs VT, Working Principle & Accuracy Classes

Jan 29, 2024

1. What Is an Instrument Transformer?

An instrument transformer is a special transformer that scales high currents and high voltages of a power system down to values that instruments, meters and relays can handle safely. Instrument transformers serve two purposes: measurement - feeding accurate, standardized signals to energy meters, ammeters, voltmeters and power-quality instruments; and protection - supplying current and voltage signals to relays so faults can be detected and cleared quickly. By isolating the low-voltage instrument side from the high-voltage network, they also protect personnel and equipment. The international product family is defined by IEC 61869 (with national equivalents such as GB/T 20840 in China), which is organized into parts: IEC 61869-1 common requirements, IEC 61869-2 for current transformers and IEC 61869-3 for inductive voltage transformers.

2. How a Current Transformer (CT) Works

A current transformer is designed so that its primary circuit carries the load current and its secondary supplies a proportional, standardized low current. In the most common design - a window or bar-type CT - the primary is a single straight conductor passing through the core, and the secondary winding is wound with many turns around the core. The transformation follows the turns ratio: if the secondary has N turns, the secondary current is approximately the primary current divided by N. For example, a CT rated 600 A/5 A has a ratio of 120:1, meaning 600 A in the primary produces 5 A in the secondary at rated load. Standard secondary outputs are 5 A or 1 A, and the rated burden (the load the CT can drive, expressed in VA) must be matched to the connected instruments. Because a CT operates near short-circuit conditions, its secondary must never be opened while the primary is energized - an open secondary can generate dangerously high voltage and damage the transformer and connected equipment.

3. How a Voltage Transformer (VT) Works

A voltage transformer, also called a potential transformer, is connected across the high-voltage line in parallel and steps the voltage down to a safe, standardized level. Its primary winding has many turns and is connected to the high-voltage side; the secondary winding has fewer turns and supplies the instruments or relays. The secondary voltage is proportional to the primary voltage divided by the turns ratio. Standard secondary voltages are 100 V (or 110 V in some systems) for phase-to-phase connection, and 100/√3 V for phase-to-neutral connection. VTs operate near no-load conditions, so - unlike CTs - a short-circuit on the secondary is the dangerous condition, and secondary protection fuses or breakers are normally installed. Both primary and secondary windings must be properly insulated and grounded per the applicable standard and utility practice.

4. Accuracy Classes for Metering and Protection

Instrument transformers are classified by accuracy. For metering, classes such as 0.2, 0.5 and 1.0 define the permissible ratio and phase errors at specified fractions of rated current or voltage; a 0.2-class CT is used for revenue metering where billing accuracy matters, while 0.5 and 1.0 cover general monitoring and instrumentation. For protection, classes such as 5P and 10P define the composite error at the rated accuracy-limit factor (for example 5P20 means the error limit is 5% up to 20 times rated current), which ensures relays see the true fault current during short circuits. When specifying, the buyer must state the application (metering or protection), the accuracy class, the rated burden, and for CTs the short-time thermal current and dynamic current ratings required by the system study.

Transformer Typical Standard Output Typical Accuracy Classes Primary Duty
Current transformer (CT) 5 A / 1 A secondary Metering: 0.2 / 0.5 / 1.0; Protection: 5P / 10P Load current measurement, fault detection
Voltage transformer (VT) 100 V / 100/√3 V (110 V class in some systems) Metering: 0.2 / 0.5 / 1.0; Protection: 3P / 6P Line voltage measurement, synchronizing, protection

5. Applications and Safety Essentials

Instrument transformers appear in every part of the power network: in substation bays for line and transformer metering and protection, in industrial switchgear panels for motor and feeder monitoring, in distribution panels for revenue metering, and in generator and grid-connection schemes where accurate phase measurement is required. Three safety rules are non-negotiable: never open the secondary circuit of an energized CT; always ground the secondary circuits of both CTs and VTs at one defined point; and never exceed the rated burden or the rated continuous current. Following these rules - and specifying the products to IEC 61869 / GB/T 20840 with the correct accuracy class and burden - keeps measurement accurate and personnel safe.

6. Selection Checklist for Buyers

When purchasing instrument transformers, confirm: the system voltage and insulation level; the type (CT, VT, or combined); the primary rating (for CT, the rated current; for VT, the primary voltage); the secondary rating (5 A/1 A for CT; 100 V class for VT); the accuracy class for the intended duty; the rated burden in VA; the frequency (50 Hz or 60 Hz); the mounting type (indoor/outdoor, bushing, window, or rack); and the applicable standard and test report. For protection applications, also confirm the accuracy-limit factor and short-time ratings, and for outdoor installations the creepage distance appropriate to the pollution level of the site.

Frequently Asked Questions

Q: What is the difference between a CT and a VT?
A: A current transformer (CT) is connected in series with the load and steps current down to 5 A or 1 A; a voltage transformer (VT) is connected in parallel and steps voltage down to a 100 V class level. They measure different quantities but serve the same two purposes: measurement and protection.

Q: Why must a CT secondary never be opened?
A: An energized CT operates like a current source; if the secondary is opened, the secondary voltage rises sharply (potentially to thousands of volts) as the core saturates, endangering personnel and insulation and possibly destroying the transformer.

Q: What do 5P20 or 10P mean on a protection CT?
A: They are protection accuracy classes: 5P means the composite error is limited to 5% (10P means 10%) at a rated accuracy-limit factor of 20 times rated current, so the relay measures fault current accurately enough to trip selectively.

Q: What is the standard secondary output of a CT?
A: 5 A is the most common; 1 A is used for long secondary cables or high-capacity substations where cable burden must be minimized. The choice affects cable sizing and relay input settings.

Q: What standards govern instrument transformers?
A: The IEC 61869 series is the international family (61869-2 for CTs, 61869-3 for inductive VTs), with national equivalents such as GB/T 20840 and IEEE/ANSI C57.13.

Q: Can one instrument transformer serve both metering and protection?
A: Yes, with multiple cores: a dual-core CT can have a 0.2-class metering core and a 5P protection core on the same primary. This is common in substation practice and keeps each duty accurate within its own class.

SEND INQUIRY

SEND INQUIRY