What the DX51D Designation Means
DX51D is the general forming grade in the family of continuously hot-dip galvanized low-carbon steels defined in EN 10346. The letters identify a steel intended for cold forming, the number indicates the forming capacity of the base steel, and the final letter indicates the coating condition. The base steel is a low-carbon, aluminium-killed grade that combines good ductility with the corrosion protection of a metallurgically bonded zinc layer.
A full material call-out therefore has three parts: the grade, the coating type and the coating mass, for example DX51D+Z275 or DX51D+AZ150. The coating mass is quoted in grams per square metre measured over both surfaces, so Z275 means 275 g/m2 in total, not 275 g/m2 on each face.
DX51D to DX54D: The Forming Grades Compared
The four standard grades in the series cover a rising scale of forming severity. DX51D is the bending and profiling grade, DX52D offers improved forming, DX53D is the deep-drawing grade and DX54D is the ultra-deep-drawing grade. The mechanical values below are the requirements of EN 10346 for the coated product.
| Grade | Yield strength Re (MPa) | Tensile strength Rm (MPa) | Elongation A80 (min, %) |
| DX51D | 270 - 500 | 270 - 500 | 22 |
| DX52D | 140 - 300 | 270 - 420 | 26 |
| DX53D | 140 - 260 | 270 - 380 | 30 |
| DX54D | 120 - 220 | 260 - 350 | 34 |
DX51D is by far the most widely traded of the four because profiling, roll forming and light bending are the dominant operations in roofing, cladding, ducting and general fabrication. The softer DX53D and DX54D grades are reserved for parts that must be drawn into shape without tearing, such as appliance housings, deep panels and complex pressings.
Coating Types and Coating Mass Designations
Two coating families are supplied on DX51D coil. Zinc coatings, designated Z, protect the steel by barrier action and by sacrificial cathodic action at cut edges and scratches. Aluminium-zinc coatings, designated AZ per EN 10346 with a nominal composition of about 55 % aluminium, 43.4 % zinc and 1.6 % silicon, give a longer life in most atmospheric exposures but protect cut edges less effectively, so they are normally used where cut edges can be sealed or are not critical.
| Coating | Mass (g/m2, both faces) | Approximate zinc thickness per face (micrometres) |
| Z40 | 40 | about 2.8 |
| Z100 | 100 | about 7 |
| Z140 | 140 | about 10 |
| Z180 | 180 | about 12.6 |
| Z275 | 275 | about 19 |
The thickness figures follow from the coating mass, the density of zinc and the fact that the stated mass covers both faces, so half of it sits on each face. They are useful when a specification is written in terms of measured coating thickness rather than mass. Aluminium-zinc coatings are lighter than pure zinc for the same volume, so an AZ150 coating of 150 g/m2 is roughly 20 micrometres thick per face, close to a Z275 zinc coating despite carrying barely half the mass. Coating mass itself is verified in the laboratory by weighing a sample before and after stripping the coating in an inhibited acid solution.
Chemical Composition of the Base Steel
Because DX51D is intended for cold forming and for coating, the chemistry is held to a low-carbon, low-residual specification. Typical maximum values under EN 10346 are:
Carbon: 0.12 % maximum
Manganese: 0.60 % maximum
Phosphorus: 0.10 % maximum
Sulphur: 0.045 % maximum
Silicon: 0.50 % maximum
Aluminium: 0.020 % minimum (as a deoxidising addition)
Copper and other residual elements are limited by the producer so that the coating adhesion and the forming behaviour of the strip are not affected. When DX51D is welded, the low carbon content keeps the heat-affected zone soft and ductile, which is why the grade is common in ducting, tube making and light structural work.
Surface Finish, Spangle and Chemical Treatment
The visual and functional finish of the coil is set by the cooling and skin-pass practice after the coating pot. Regular spangle shows the large crystalline grain pattern produced by normal solidification; minimised spangle reduces the grain size; spangle-free surfaces are produced by suppressing grain growth so that the sheet paints to a uniform appearance. A skin-pass roll can also be applied to improve flatness and to develop the surface texture required for painting.
After coating, the strip may be given a chromate-free passivation treatment for storage protection, or an oil film for forming, or a phosphate treatment for paint adhesion. These treatments are stated separately from the coating designation and must be carried through to the mill certificate.
Ordering, Inspection and Supply
DX51D galvanized coil is normally ordered by grade, coating type and coating mass, dimensions and tolerance class, coil mass, and surface treatment. Common supply ranges are thickness from about 0.25 mm to 2.0 mm, width from about 600 mm to 1500 mm, coil inner diameter of 508 mm or 610 mm, and coil mass from about 3 t to 15 t, all subject to the mill concerned. Dimensional tolerances for continuously hot-dip coated steel are specified in EN 10143.
On delivery the coil should be checked against the EN 10204 inspection document for grade, coating designation, coating mass, coating type or spangle, surface treatment and mechanical properties. The coil should be inspected for edge damage, kinks, dents and transit corrosion, and the zinc coating weight should be confirmed when the order calls for it. Coils must be stored under cover, clear of the floor, with air circulating around the wraps, because condensation between wraps is the usual cause of white rust in storage.
Frequently Asked Questions
Q: What does the Z in Z275 mean?
Z identifies a zinc coating, and 275 is the total coating mass in grams per square metre across both surfaces, which corresponds to roughly 137.5 g/m2 and about 19 micrometres on each face.
Q: Is DX51D a structural steel grade?
No. DX51D is a forming grade for cold-formed and profiled products. Structural strength must be demonstrated by the section and the design code, not by the coil grade alone, and higher-strength coated grades such as S250GD or S350GD are used where structural capacity is required.
Q: Can DX51D be welded?
Yes. The low carbon and low residual chemistry gives good weldability by resistance and arc processes, although the coating should be removed from the weld zone to avoid porosity and zinc fume.
Q: How is the coating mass verified?
A known-area sample is weighed, the coating is dissolved in inhibited acid, the sample is reweighed, and the mass loss is converted to grams per square metre for both faces.
Q: Which is better, zinc or aluminium-zinc coating?
Aluminium-zinc gives a longer life in rural and industrial atmospheres for the same coating mass, while zinc is more economical and protects cut edges and scratches by sacrificial action. The choice follows the exposure and how the edges will be treated.
Q: What documents should accompany a coil?
An EN 10204 inspection certificate, normally type 3.1 for structural and specification-critical orders, stating grade, coating designation, coating mass, spangle, surface treatment and mechanical properties.


