Home-Knowledge-

Content

SGCC Galvanized Steel Coil for Metal Stamping

Oct 29, 2025

1. What Is SGCC Galvanized Steel Coil?

SGCC is a steel grade designation defined in JIS G3302 (hot-dip zinc-coated steel sheet and strip). It denotes commercial-quality galvanized steel - a cold-rolled or hot-rolled steel substrate coated with a protective zinc layer in a continuous hot-dip line. The steel strip is cleaned, annealed, and passed through a bath of molten zinc at approximately 450°C; an air knife then controls the coating weight across the full width, and the strip is cooled, leveled and recoiled.

The resulting material combines the mechanical strength of the steel base with the sacrificial corrosion protection of zinc. In humid or mildly corrosive environments, the zinc coating corrodes preferentially and protects the steel substrate even at small scratches or cut edges - the well-known cathodic protection mechanism that makes galvanized steel a reliable, low-maintenance material for stamping-intensive industries.

2. Why SGCC Is a Preferred Input for Metal Stamping

Metal stamping places demanding requirements on the incoming coil: consistent gauge, clean surface, and a coating that survives severe deformation without flaking. SGCC and related grades (DX51D+Z per EN 10346) satisfy these needs:

Coating adhesion: the zinc-iron alloy layer formed during hot-dipping bonds metallurgically with the substrate; properly specified coils pass a 180° bend test without coating separation.

Formability: commercial-quality galvanized grades offer the ductility needed for blanking, punching, deep drawing and roll forming of medium-complexity parts.

Consistent tolerances: mill-level gauge control supports repeatable die performance and reduces scrap in high-volume stamping lines.

Corrosion head-start: stamped parts keep the zinc layer after forming, so finished components can skip additional painting where service conditions allow.

3. SGCC Coil Technical Parameters

Parameter Available Range (typical mill supply)
Product form Galvanized steel coil / sheet / strip (GI)
Steel grades DX51D, DX52D, DX53D, DX54D (EN 10346); SGCC (JIS G3302); S250GD-S550GD (structural)
Thickness 0.1 - 6.0 mm
Width 30 - 1500 mm
Coating process Hot-dip galvanizing (continuous line)
Zinc coating mass Z30 - Z600 (g/m², total both sides)
Surface treatment Chromated / passivated, skin-passed, oiled, slightly oiled, dry
Spangle Zero spangle / regular spangle / minimized spangle
Coil weight 3 - 10 t per coil, or per customer requirement
Coil ID 508 mm / 610 mm

Indicative mechanical values (hot-dip, per EN 10346):

Grade Yield strength (MPa) Tensile strength (MPa) Elongation (%)
DX51D+Z ≤360 (typical) 270-500 ≥20
DX52D+Z 140-300 270-420 ≥22
DX53D+Z 140-260 270-380 ≥26
DX54D+Z 140-220 270-350 ≥30
S250GD+Z ≥250 330-430 ≥17
S350GD+Z ≥350 420-520 ≥16
S550GD+Z ≥550 ≥560 -

4. Application Scenarios

Petrochemical: galvanized SGCC coil is used for equipment enclosures, cable trays, ventilation ducts, and non-pressure components where corrosion resistance reduces maintenance frequency.

Construction: profiled roofing sheets, wall panels, purlins, scaffolding components and light steel structures benefit from the coating's durability and long service life.

Light industry & appliances: stamping blanks for hardware, furniture fittings, office equipment, electrical enclosures and appliance casings use SGCC where surface quality and formability are required.

Automotive aftermarket & general fabrication: brackets, mounting plates and protective covers are typical stamping outputs from SGCC coil.

Note: for structural load-bearing members, specify structural grades (S-series per EN 10346 or SGHC per JIS G3302) instead of commercial grades.

5. How to Specify SGCC Coil Correctly (Buyer's Checklist)

Grade & standard: state the governing standard (JIS G3302, EN 10346, ASTM A653) and grade (e.g., SGCC, DX51D+Z).

Coating class: choose Z (zinc mass per m² total both sides) according to the service environment - light indoor use can accept Z40-Z80; outdoor exposure generally needs Z180-Z275 or higher.

Surface treatment: specify passivation (chromated or chromium-free), oiling, or dry; skin-passed surface if a smooth, matte finish is required for painting.

Spangle: regular, minimized or zero spangle - zero spangle is preferred for painted or highly aesthetic surfaces.

Dimensions & coil weight: confirm thickness, width, coil ID (508/610 mm) and max coil weight against your stamping press and handling equipment.

Documentation: request mill test certificates (EN 10204 type 3.1 or 2.2) and, if required, independent third-party inspection.

Frequently Asked Questions

Is SGCC the same as DX51D? Not identical, but they overlap in practice. SGCC is the JIS G3302 commercial-grade designation; DX51D is the EN 10346 designation for continuous hot-dip coated steel for cold forming. Many mills supply SGCC coils that also meet DX51D requirements, but always confirm the governing standard and mechanical values on the mill certificate before substitution.

What zinc coating class should I choose for outdoor roofing? For outdoor roofing and wall cladding, a coating class of Z180-Z275 g/m² (total both sides) is commonly recommended. Lighter classes such as Z40-Z80 are for indoor parts and will rust prematurely in open air, especially in coastal or industrial atmospheres.

Can SGCC coil be deep drawn? Commercial-grade SGCC supports moderate forming and shallow-to-medium drawing. For deep drawing or complex stamping, choose a drawing-grade material (e.g., DX53D, DX54D or DC-series cold-rolled substrate) and verify the coating withstands the drawing process without powdering.

Why does my galvanized coil rust at the cut edges? Cut edges expose the steel substrate. Zinc's cathodic protection limits rust creep near the edge, but in wet conditions edge rust can still develop. Specify heavier coating classes, use edge protection (e.g., edge sealer for tight-cut components), or apply zinc-rich paint after cutting for critical parts.

What is the difference between hot-dip and electro-galvanized coil? Hot-dip coating (SGCC, DX51D+Z) delivers a thicker zinc layer (typically Z40-Z600) with excellent corrosion resistance and is produced in continuous galvanizing lines. Electro-galvanized coil carries a much thinner, smooth coating (typically tens of g/m²), offering superior surface finish and weldability for appliance and automotive interior parts, but with shorter corrosion life.

Can SGCC galvanized coils be supplied in slit widths and cut lengths? Coils can be slit to widths from 30 mm upward and cut to length into sheets, with packing arranged to the order specification. Width, thickness, coating class and quantity are confirmed against the mill certificate before dispatch.

SEND INQUIRY

SEND INQUIRY