Home-Knowledge-

Content

GI Corrugated Sheet: Profiles, Coatings and Building Applications

May 09, 2024

A GI corrugated sheet is a profiled building sheet formed from zinc coated steel strip, usually on a roll-forming line that turns flat coil into a repetitive wave or trapezoidal section. The galvanized substrate supplies stiffness and load capacity through its folded geometry, while the zinc coating supplies the corrosion resistance that lets a sheet as thin as 0.3 mm survive decades of weather. The result is a light, inexpensive and very durable cladding material used on roofs, walls, sheds, culverts and temporary works worldwide.

Choosing the right sheet means matching three variables to the job: the profile geometry, the base steel thickness and the coating mass. Getting the profile right controls span capacity and appearance, thickness controls stiffness and screw-holding strength, and coating mass controls how long the sheet lasts before rust appears.

What a GI Corrugated Sheet Is

The substrate is low-carbon steel strip, either hot rolled or cold rolled, coated on a continuous hot-dip line. The strip is uncoiled through an accumulator, cleaned and annealed, then drawn through a molten zinc bath at about 450 to 460 °C before the coating mass is controlled by gas wiping. The coated strip is cooled, may receive a passivation or anti-fingerprint treatment, and is then slit and roll formed into the finished profile. Because roll forming happens after coating, the zinc layer is stretched at every bend, so the coating must remain ductile enough to follow the profile without cracking.

The classic corrugated section is a rounded sinusoidal wave, while trapezoidal sections use flat pans joined by inclined webs to give higher load capacity per unit of steel. Both are made from the same galvanized coil and both are covered by the same coating standards, so the choice between them is a structural and visual decision rather than a coating decision.

How the Zinc Coating Protects the Sheet

Zinc protects steel in two ways. It acts as a barrier that keeps moisture and oxygen away from the steel surface, and it acts as a sacrificial anode, corroding preferentially at scratches, cut edges and fastener holes so that the exposed steel beside the damage does not rust. During the hot-dip process a series of zinc-iron alloy layers forms at the interface, which metallurgically bonds the coating to the substrate and prevents it from peeling during forming and handling.

Coating mass is specified in grams per square metre of sheet surface and is written as a Z designation in metric standards, or as a G designation in inch-pound practice where the value expresses total coating weight on both faces in ounces per square foot. Coating selection is a straightforward function of environment and required service life.

Coating class Mass (g/m²) Suitable context
Z40 40 Painted interior surfaces, dry enclosed use
Z100 100 General indoor use, sheltered interior linings
Z180 180 Normal outdoor building use with regular rain washing
Z275 275 Aggressive environments, long-life exposed roofs and walls

In ASTM practice the same classes are written G40 to G185, where G90 corresponds approximately to the 275 g/m² metric class. Whichever notation is used, the sheet should be ordered and certified against EN 10346 or ASTM A653/A653M so that the coating mass can be verified by testing rather than assumed.

Corrugated Profiles and Sheet Geometry

Profile geometry determines how a thin sheet carries load. Depth increases stiffness far more effectively than thickness, because the section modulus of a folded sheet grows with the square of the depth, so a deeper profile made from thinner steel usually outperforms a shallow profile made from thicker steel. Pitch, the centre-to-centre distance between adjacent crests, affects the number of fastening points and the appearance of the finished roof.

Sinusoidal or wave profile: the traditional corrugated iron shape, typically a rounded wave with a pitch of about 76 mm and a depth of about 18 mm, familiar on agricultural buildings and utility structures.

Trapezoidal profile: flat pans with inclined webs, commonly pitched between 125 mm and 250 mm with depths from about 25 mm to 50 mm, giving greater span capacity for the same steel thickness.

Narrow-pitch micro profiles: used for wall cladding, vehicle bodies and decorative panels where a fine rib pattern is wanted.

Structural decking profiles: deep trapezoidal sections designed to act as permanent formwork or as a stressed skin in composite floors.

Two widths matter on every order. Overall width is the full width of the sheet as delivered, while cover width, or effective width, is the width actually covered once sheets are lapped together. Cover width is always smaller, sometimes by 60 to 100 mm, and it is cover width that must be used when calculating how many sheets a roof requires.

Thickness, Coating Mass and Finish Selection

Base thickness Typical duty
0.14 mm to 0.20 mm Temporary cover, packaging, light agricultural screening
0.20 mm to 0.30 mm Economical agricultural roofing and fencing, short-span cladding
0.30 mm to 0.50 mm Mainstream roof and wall cladding on industrial and residential buildings
0.50 mm to 0.80 mm Load-bearing decking, long spans, walkable roofs, higher screw pull-out strength
0.80 mm to 1.20 mm Heavy duty sheeting, formwork, corrugated drainage structures

Surface finish is chosen alongside thickness and coating mass. Regular spangle sheet shows the crystalline zinc pattern and is the standard finish; minimised spangle or skin-passed sheet is smoother and is preferred when a uniform painted appearance matters. Passivation treatments protect the surface during storage and transport, while anti-fingerprint films reduce handling marks before painting. Factory-applied organic coatings, standardized in EN 10169 and ASTM A755/A755M, combine the metallic coating with a polyester, plastisol or PVDF paint system and give the longest service life and widest colour choice for exposed architectural work.

Applications, Fixing and Site Practice

Corrugated galvanized sheet covers roofing and wall cladding on factories, warehouses, farm buildings and houses; grain stores and silos; fencing and hoardings; formwork and permanent shuttering; drainage culverts and small bridges made from corrugated steel pipe; and increasingly the mounting structures of ground-mounted solar arrays. In each case the profile, thickness and coating mass are selected together, and the specification should state all three rather than only the sheet thickness.

Fix through the crest adjacent to each side lap using self-drilling screws fitted with sealing washers, driven with a depth-sensitive tool so the sheet is not crushed or dimpled.

Take purlin spacing from the load-span table for the selected profile and thickness, and reduce it where snow or wind uplift governs.

Allow for thermal movement. Sheets expand and contract with surface temperature, so use slightly oversized fastener positions rather than rigidly clamping every fixing.

Observe minimum end laps and side laps for the roof pitch, and place lap sealant or butyl tape in end laps where water can pond or be driven by wind.

Protect cut edges on exposed long-life work. Sheared edges expose uncoated steel, so treat them with a zinc-rich repair product or cover them behind laps and flashings.

Separate dissimilar metals. Do not let coated sheet come into continuous contact with copper, lead or bare carbon steel, and use coated or stainless fasteners appropriate to the environment.

Cut with shears or nibblers where possible. Abrasive cutting throws hot sparks that damage the coating and leaves swarf that rusts on the surface.

Inspection on delivery is quick but worthwhile: check overall and cover width, base thickness, coating class marked on the bundle label, and the mill certificate covering coating mass and mechanical properties. Reject sheets with coating skip, coating cracks at bends, deep transit dents or white storage staining caused by wet stacking, because each of these becomes a corrosion initiation site once the sheet is installed.

Frequently Asked Questions

Q: What does GI mean in GI corrugated sheet?
GI stands for galvanized iron, the traditional name for sheet steel protected by hot-dip zinc coating. Modern GI sheet is made from low-carbon steel strip, not iron, but the abbreviation has remained in common commercial use.

Q: Which coating class should be used for a farm building roof?
A Z180 coating is a sensible minimum for normal rural roofing, while Z275 is preferred where the building is near the coast, downwind of industry or expected to give a very long service life without repainting.

Q: Is thicker sheet always better than a deeper profile?
Not necessarily. Because stiffness rises rapidly with profile depth, a deeper profile in thinner steel can be both stronger and lighter than a shallow profile in thicker steel. Span tables for the actual profile should decide the answer.

Q: Can GI corrugated sheet be painted?
Yes, after cleaning and appropriate pretreatment. Factory-applied coatings give the most durable result because the strip is cleaned, pretreated and coated under controlled conditions; site painting works best on new, clean, passivated sheet.

Q: Why does the sheet rust at the cut edges first?
The shear cuts through the zinc coating and exposes bare steel, so corrosion starts at the cut face and at fastener holes. Cut-edge protection and correctly sized, sealing washers slow this process considerably on exposed work.

Q: How should corrugated sheets be stored before installation?
Under cover, dry, off the ground and with adequate ventilation between sheets. Bundles stored in damp conditions or stacked with standing water between sheets develop white or dark storage stain that is difficult to remove and reduces coating life.

SEND INQUIRY

SEND INQUIRY