Home-Knowledge-

Content

Cold Galvanizing vs Hot Dip Galvanizing: Coating Differences

Oct 09, 2025

Two Processes That Only Share a Name

Cold galvanizing and hot dip galvanizing both use zinc to protect steel, but they work through different mechanisms and deliver very different coating masses. Cold galvanizing, sometimes called zinc rich painting, relies on a coating in which zinc particles are bound in an organic or inorganic binder and applied by brush, roller or spray at ambient temperature. Hot dip galvanizing immerses prepared steel in molten zinc, typically at about 450 degrees Celsius, so alloying reactions at the interface create a metallurgically bonded coating rather than an applied film.

Coating Structure and Mass

Feature Cold galvanizing Hot dip galvanizing
Application temperature Ambient About 450 degrees Celsius
Bond type Adhesive film Metallurgical iron-zinc alloy plus pure zinc
Typical zinc mass 10-50 g/m2 From about 145 g/m2 upward, 20 micrometres and above
Thickness control Thin, uniform by coats Governed by dipping time and withdrawal speed
Field repairability Easy, single component touch up Requires zinc rich repair compound on site

This mass difference is the reason the two methods age at different rates. A cold galvanized layer measured in tens of grams per square metre cannot match a 275 g per square metre continuous galvanized coil coating, and it is normally chosen where the structure is too large for a bath or where only local protection is needed.

How Zinc Protects Steel

Zinc protects steel in two ways. As a barrier it isolates the substrate from moisture and oxygen, and a stable film of zinc oxide, zinc hydroxide and basic zinc carbonate forms on the surface and slows further attack. That film, sometimes seen as white rust, is repeatedly broken down and reformed during service without consuming the coating at an uncontrolled rate. As a sacrificial anode it works electrochemically: the standard potential of zinc is minus 0.76 volts against minus 0.44 volts for iron, so in a galvanic couple zinc dissolves as the anode and the steel remains the protected cathode. This is why a scratched galvanized surface continues to resist corrosion at the damaged area until the surrounding zinc is exhausted.

Bath Chemistry and the Alloy Layer

In hot dip galvanizing the workpiece enters molten zinc and an iron-zinc alloy layer forms first at the interface, followed by an outer layer of nearly pure zinc. The alloy layer grows by interdiffusion of iron and zinc, and its thickness depends on bath temperature, immersion time and the silicon and phosphorus content of the steel. Silicon above roughly 0.04 percent can accelerate alloy growth and produce an excessively thick, brittle coating, which is why steel intended for hot dip galvanizing is often specified with restricted silicon. At service temperatures above about 220 degrees Celsius the interdiffusion continues in the solid state, and the difference in diffusion rates between iron and zinc causes voids at the interface, a phenomenon known as the Kirkendall effect.

Selecting the Right Protection for a Project

Use continuous hot dip galvanized coil where a uniform, factory controlled coating mass is required on large production volumes of sheet and strip.

Choose batch hot dip galvanizing for finished fabrications such as frames, lattice structures and platforms, where the coating must cover all surfaces including internal corners.

Use cold galvanizing for touching up welds, cut edges and mechanical damage on site, and for small parts that cannot justify a bath run.

Do not rely on cold galvanizing alone for submerged or continuously wet service, where a thicker hot dip coating or a duplex system is required.

When combining zinc with paint, allow the specified curing interval; a fully cured coating gives the adhesion needed for the duplex build.

For hot dip galvanized product the coating mass is verified gravimetrically on a measured coupon, and coating thickness is checked with a magnetic gauge at multiple positions. Adhesion is assessed by bending or cupping to the specified radius and inspecting for flaking, and appearance is judged against the agreed spangle and surface condition. For cold galvanized films, the checks are dry film thickness, cure condition and adhesion by cross hatch, since the protection depends on film integrity rather than on alloying. Inspection records to EN 10204 type 3.1 with a declared coating class on the mill certificate are the normal commercial evidence for continuous galvanized coil.

Frequently Asked Questions

Q: Is cold galvanizing as durable as hot dip galvanizing?

A: No. A cold galvanized film deposits only 10 to 50 grams of zinc per square metre, far less than a hot dip coating, so its service life in an aggressive environment is much shorter.

Q: Can cold galvanizing be used to repair a hot dip coating?

A: Yes, zinc rich repair compounds are the accepted method for touching up welds, cut edges and handling damage on site.

Q: Why does hot dip galvanized steel have a spangled appearance?

A: The visible pattern is the crystalline zinc grain structure formed as the coating solidifies, and its size can be controlled by the mill.

Q: What causes white rust on galvanized steel?

A: Moisture trapped between stacked surfaces reacts with zinc to form zinc hydroxide and basic zinc carbonate, which appears as a white deposit; dry storage and passivation limit it.

Q: At what temperature does a hot dip coating degrade?

A: Service above about 220 degrees Celsius accelerates iron-zinc interdiffusion and can lead to coating detachment, so continuous service is usually limited to that level.

SEND INQUIRY

SEND INQUIRY