What Makes DC07 Different
DC07 sits at the top of the cold rolled forming family defined in EN 10130 and is listed under the material number 1.0898 in the German designation system. Where DC01 handles bending and DC04 handles conventional deep drawing, DC07 is engineered for ultra deep drawing: parts with steep walls, tight radii, multi-stage draws and geometries that would tear in a lesser grade. The grade achieves this through a very low carbon, titanium stabilised interstitial free chemistry combined with a full annealing cycle that produces a coarse, favourably oriented grain structure and an exceptionally low yield strength.
Mechanical Properties and Chemistry
| Property | DC07 requirement |
|---|---|
| Yield strength Re | 150 MPa max. |
| Tensile strength Rm | 250-310 MPa |
| Elongation at fracture A80 | 44 % min. |
| Plastic strain ratio r90 | 2.5 min. |
| Strain hardening exponent n90 | 0.230 min. |
| Phosphorus, P | 0.020 % max. |
| Sulfur, S | 0.020 % max. |
The combination of a high r90 value and a high n90 value is what makes DC07 work in a difficult die. A high plastic strain ratio means the sheet resists thinning in the wall of the drawn part, because the material flows preferentially in the plane of the sheet rather than through its thickness. A high strain hardening exponent means the material keeps hardening as it stretches, which delays the onset of local necking and distributes strain more evenly around the punch. Low phosphorus and sulfur limits remove the inclusions and the embrittling effects that would otherwise initiate cracks under the severe strains of an ultra deep draw.
Forming Performance in Practice
Single stage draws that are beyond the capacity of DC04, and multi-stage sequences involving redrawing, flanging and ironing, are the natural applications.
Springback is low because the yield strength is low, so formed parts hold their shape with less overbending than higher strength grades.
Tool loads drop relative to stronger grades, which extends die life and reduces press tonnage requirements on marginal jobs.
Because the material is stabilised, it does not age; press behaviour remains consistent from the first blank to the last after months in store.
Blank holder force and lubricant must be tuned to the grade, since excessive restraint on such a ductile material produces wrinkles rather than tears.
Surface Quality and Its Effect Downstream
DC07 is rolled, annealed and temper rolled to a very smooth, low roughness surface with a minimum of surface defects. This matters beyond appearance: a smooth surface reduces the amount of paint, zinc or electroplating required to achieve full coverage, which lowers consumption of coating material and improves consistency of the finished film. The low roughness also means that references to surface quality class follow EN 10130, with exposed part quality ordered where the formed surface will remain visible after painting. Roughness and peak count are quoted when the customer paints the part, because those parameters influence both paint flow out and adhesion.
Delivery, Certification and Ordering
DC07 is supplied as cold rolled coil, slit strip and cut to length sheet, typically from 0.30 mm to 2.00 mm thick and up to about 1450 mm wide, with coil weights of 3 to 8 tonnes and inner diameters of 508 mm or 610 mm. Surface condition is normally oiled to protect the exceptionally clean surface during transport and storage. Inspection documents to EN 10204 type 3.1 report the tensile test results to EN ISO 6892-1 together with the r90 and n90 values from ISO 10113 and ISO 10275, because these are the parameters that govern forming simulation and die approval. Thickness tolerances follow EN 10131 and should be stated on the order together with flatness class and edge condition, since half tolerance and restricted flatness affect both yield and price.
Frequently Asked Questions
Q: Is DC07 suitable for ordinary bending work?
A: It is capable of it, but the extra cost is not justified; DC01 or DC03 delivers the same result at a lower price.
Q: What is the material number for DC07?
A: DC07 corresponds to material number 1.0898 in the German designation system.
Q: Why does DC07 have such a high elongation?
A: A stabilised, very low carbon chemistry combined with full annealing produces the soft, favourably textured structure that allows the grade to reach 44 percent minimum elongation at 80 mm gauge length.
Q: Does DC07 age in storage?
A: No. The interstitial elements are tied up by stabilising additions, so the forming properties remain stable during storage.
Q: Which thickness range is produced?
A: Production commonly runs from 0.30 mm to 2.00 mm, and the order should state thickness, width, tolerance class and coil weight.


