Home-Knowledge-

Content

DX51D Galvanized Steel Coil: Properties and Applications

Oct 17, 2025

DC51D-Z(2).pdf

Reading the DX51D Designation

In the DX51D designation the letters DX indicate a flat product intended for cold forming, and the base substrate is either cold rolled steel, corresponding in property terms to the DC01 class, or hot rolled steel of the DD11 class. The number 51 identifies the series and the grade level: higher numbers such as 52, 53 and 54 mark increasing formability, with steadily lower yield windows and higher elongation minimums. The final D indicates that the material is suited to bending and forming. DX51D is therefore the entry grade of the forming family, and this is precisely why it dominates commercial volume.

Mechanical Properties and Coating Classes

Parameter DX51D DX52D DX53D
Tensile strength Rm 270-500 MPa 270-420 MPa 270-380 MPa
Yield strength Re Not fixed by EN 10346, mill range about 140-300 MPa 140-300 MPa 140-260 MPa
Elongation A80 min. 22 % 26 % 30 %
Typical coating Z100 to Z275 Z100 to Z275 Z100 to Z275

EN 10346 deliberately leaves the yield strength of DX51D unfixed, because the acceptance criterion for coated product is the tensile and elongation behaviour rather than a guaranteed yield value. Buyers who need a guaranteed yield strength should move to a structural designation such as S250GD or S350GD, which carry defined minimum yield values along with the same coating options. Coating mass runs from Z100 for indoor ducts up to Z275 for cladding and industrial service, with heavier classes such as Z350 produced to order. Surface structure may be regular spangle, minimised spangle or skin passed, and surface treatment may be passivated, oiled, or passivated and oiled together.

Where DX51D Performs Best

HVAC ducting and ventilation components, where the substrate is thin, the forming is simple and the coating only has to resist indoor condensation.

Roof and wall cladding, where Z275 provides the corrosion allowance required for decades of external exposure.

Cable trays, trunking and light support brackets, produced by press brake bending or roll forming.

Appliance casings and internal panels, where surface appearance and paint adhesion matter more than strength.

Packaging frames, shelving and general sheet metal work, where the grade gives an economical balance of properties.

Processing, Welding and Paint Adhesion

DX51D is rolled and bent with standard mild steel practice, and a minimum inner bend radius of roughly one times thickness at 180 degrees avoids coating cracking. Roll forming is widely used for long profiles, and the coating tolerates the modest strain involved. For welding, spot welding is standard, and the zinc coating must be considered in the electrical and ventilation parameters because it melts and vaporises at the weld; extraction is part of the process design. The surface is well prepared for painting: after appropriate cleaning and pre-treatment, the passivated or oiled surface takes polyester, polyurethane and epoxy systems with good adhesion. Where the panel is formed before painting, a chromate free pre-treatment keeps the process compatible with restricted substances requirements.

Supply and Quality Control

DX51D galvanized coil is supplied from 0.30 mm to 3.00 mm thick and 800 mm to 1500 mm wide, with coil weights from 3 to 8 tonnes and inner diameters of 508 mm or 610 mm. Coating mass, spangle type and surface treatment are stated in the order and on the certificate, and inspection documents to EN 10204 type 3.1 accompany the shipment. Tensile testing follows EN ISO 6892-1, coating mass is determined gravimetrically, and coating adhesion is checked by bending or cupping the coated sample. Slitting to narrow width, cut to length sheet and custom packing with edge protection are available for export handling.

Frequently Asked Questions

Q: What is the difference between DX51D and SGCC?

A: DX51D is defined in EN 10346 and SGCC in JIS G3302; both are commercial forming grades and are frequently treated as equivalents, but guaranteed values and coating designations differ.

Q: Does DX51D have a specified yield strength?

A: No. EN 10346 does not fix a yield strength for DX51D, though mill data usually falls between about 140 and 300 MPa.

Q: Which coating should be ordered for outdoor cladding?

A: Z275 is the normal choice for external building applications, with heavier classes available where the environment is aggressive.

Q: Can DX51D be used for deep drawn parts?

A: DX51D is a bending and forming grade; for deep drawing, DX52D, DX53D or a cold rolled DC04 class substrate is the better selection.

Q: How is the zinc coating measured?

A: Coating mass is determined gravimetrically on a coupon of known area, and magnetic thickness gauges are used for routine checking across the strip.

SEND INQUIRY

SEND INQUIRY