What DC03 Is and Where the Designation Comes From
DC03 is a cold-rolled, low-carbon steel sheet and strip intended for cold forming. The designation belongs to the EN 10130 series, which covers cold-rolled flat products of low-carbon steel for cold forming and runs from DC01 to DC07. In the code, the leading D marks a flat product for cold forming and the C states that the product is cold rolled, while the two digits rank the forming capability of the grade.
The older German standard DIN 1623-1 used names such as St 12, St 13 and St 14 for the same family, and those names were withdrawn when the current European designation system took over. A drawing that still calls for a DIN 1623-1 grade should be converted to the current EN 10130 designation before the material is ordered, because the two systems rank formability in the same way but do not use the same names.
Where DC03 Sits in the EN 10130 Series
| Grade | Forming class | Typical use |
|---|---|---|
| DC01 | Commercial quality | Bending, profiling and simple presswork |
| DC03 | Drawing quality | Stamped and drawn parts of moderate severity |
| DC04 | Deep drawing quality | Deeper drawn parts and formed load-bearing components |
| DC05 | Extra deep drawing quality | Severe draws in appliance and automotive panels |
| DC06 and DC07 | Interstitial-free extra deep drawing | The most severe forming operations, with non-ageing behaviour |
DC03 is therefore the grade to quote when a part is genuinely formed rather than merely bent, but when the draw depth is still moderate. Moving up to DC04 or DC05 raises the cost, and the extra ductility is wasted if the press tool does not need it.
Cross-Reference to Other Standards
| Standard system | Grade or class | Comment |
|---|---|---|
| EN 10130 | DC03 | Base specification for the cold-rolled forming grade |
| JIS G 3141 | SPCD | Drawing quality, with SPCE quoted where forming is more severe |
| GB/T 5213 | DC03 | Same designation family; also supplied against the legacy 08Al deep-drawing grade |
| ASTM A1008/A1008M | Drawing and deep drawing steel | Formability is defined by mechanical properties, so the match is approximate |
| Withdrawn DIN 1623-1 | St 13 class | Older designation for a comparable forming level |
A cross-reference table is a starting point for discussion, not a substitution rule. SPCD and DC03 are produced to different chemistry controls and are tested on different samples, and the same is true of any ASTM grade that is defined by mechanical properties rather than by a composition table. Where a part is critical, the grade should be ordered to the standard named on the drawing.
Typical Mechanical and Dimensional Data
The values below describe DC03 in the annealed and skin-passed condition, which is how the grade is normally delivered. They are typical figures for specification discussion, and the guaranteed values are those of the standard and of the mill certificate that applies to the ordered product.
| Property | Typical value |
|---|---|
| Yield strength | 120 MPa to 240 MPa |
| Tensile strength | 270 MPa minimum |
| Elongation | 32 percent minimum |
| Thickness | 0.20 mm to 3.00 mm |
| Width | 45 mm to 2200 mm, subject to rolling line capability |
| Coil inner diameter | 508 mm or 610 mm |
| Coil weight | 3 t to 5 t, or as agreed for the order |
| Surface condition | Bare, oiled, or with a protective film |
DC03 is aluminium-killed and delivered after cold rolling, annealing and skin passing. Skin passing is what gives the surface the flat, strain-free appearance needed for painting, and the amount of skin-pass reduction is a producer process parameter rather than a grade requirement. Where the sheet will be painted and the appearance matters, both the surface finish and the surface quality class must be ordered explicitly, because those attributes are not implied by the grade alone.
Formability, Surface and Typical Applications
Appliances: panels, doors and internal parts of washing machines, refrigerators and ovens.
Automotive: brackets, interior structural parts and panels that are formed but not exposed to the most severe draws.
Electrical and electronic equipment: enclosures, cabinets and chassis parts.
Building and furniture hardware: formed profiles, brackets and fittings, usually supplied painted or powder coated.
DC03 is a forming grade and is not ordered by yield strength for structural design. If a minimum yield strength is needed for a load-bearing part, a structural grade should be specified instead, and the forming behaviour of that grade should then be checked against the tool. The same rule applies to the coated product: where DC03 substrate is hot-dip coated, the coated sheet is ordered to the coating standard with the substrate named on the order, and the coating changes the friction and the formability at the press.
Frequently Asked Questions
Q: Is DC03 equivalent to SPCC?
No. SPCC is the commercial quality grade of JIS G 3141, which corresponds more closely to DC01. DC03 is a drawing quality grade and is usually compared with SPCD, with SPCE quoted when the forming is more severe.
Q: Is DC03 the same as 08Al?
The two are close in forming behaviour. 08Al is the legacy Chinese deep-drawing grade, and DC03 to GB/T 5213 is supplied for comparable applications, but the chemistry and the mechanical guarantees are not identical.
Q: What thickness is DC03 available in?
Cold-rolled DC03 is normally supplied from about 0.20 mm to 3.00 mm, with the exact range depending on the width and the rolling mill. Heavier sections belong to the hot-rolled or pickled product range rather than to cold-rolled sheet.
Q: Can DC03 be galvanized?
Yes. Cold-rolled DC03 substrate can be hot-dip coated, and the coated product is then ordered to the coating standard with the substrate stated on the order. The coating influences friction and forming behaviour at the press.
Q: Is DC03 a structural steel?
No. DC03 is a forming grade and is not ordered by yield strength for structural design. Where a minimum yield strength is required for a load-bearing part, a structural grade should be specified instead.
Q: Does DC03 have to be supplied oiled?
Oiling is a delivery condition, not a grade requirement. Lightly oiled surfaces are common for transport and storage, and the sheet can be supplied bare where the forming line prefers it.


