What GA and GI Stand For
GI, hot dip galvanized, is produced by passing cold rolled strip through a molten zinc bath so that the steel leaves the line carrying a coating that is essentially pure zinc. GA, galvannealed, starts with exactly the same zinc bath, but after the strip leaves the bath it is reheated in an in-line induction or gas furnace for a few seconds, and during that short anneal iron from the steel diffuses into the zinc layer and converts the coating into a zinc-iron alloy.
This is why the GA versus GI question is really a question about the post-dip thermal treatment rather than about the steel substrate. Both products run on the same continuous galvanizing line, both are supplied as coil, sheet or blank, and both protect steel with zinc. What changes is the chemistry and morphology of the coating, and with it the surface appearance, the welding behaviour, the way paint adheres and the way an exposed cut edge behaves in service.
Coating Structure and Composition Compared
| Property | GI, coating code Z | GA, coating code ZF | Aluminium-zinc, coating code AZ |
|---|---|---|---|
| Coating composition | Essentially pure zinc | Zinc-iron alloy, iron typically 8 to 12 percent | About 55% aluminium, 43.4% zinc and a small silicon addition |
| Appearance | Bright metallic surface with visible spangle | Matt, uniform grey surface without spangle | Fine spangle, light metallic sheen |
| Coating hardness | Soft and ductile | Hard, intermetallic layers | Harder than zinc, brittle in thick coatings |
| Typical coating mass | Z100 to Z350 total on both surfaces | Commonly 40 to 60 grams per square metre per side | AZ100 and AZ150 total on both surfaces |
| Cut edge protection | Good, zinc protects steel sacrificially | Limited, little sacrificial action | Limited, the aluminium rich layer is mainly a barrier |
The coating codes above follow EN 10346 and are echoed in the coating classes of the equivalent national standards, so a mill certificate should always be read as type plus mass, for example a pure zinc coating of 275 grams per square metre total or a zinc-iron coating of a stated mass per side.
Welding, Forming and Painting Behaviour
Resistance spot welding. GA is generally the easier substrate to weld. Its harder alloy coating has a higher surface resistance, which makes welding current more consistent and gives longer electrode life, whereas GI demands a higher current and closer electrode dressing and tip change discipline because the low resistance zinc layer diverts current and alloys with the copper electrode.
Forming. GI has the ductile coating, so it survives bending, roll forming and moderate drawing with little surface damage. The hard intermetallic layers of GA can powder or flake when the coating is over-alloyed or when forming strains are severe, so automotive users specify powdering and flaking limits and control the iron content of the coating.
Painting. GA is the standard substrate for painted automotive and appliance panels because its matt, textured alloy surface keys well to paint and does not need the conversion coating that a smooth zinc surface requires. GI can be painted reliably, but only after a proper pretreatment such as a phosphate or chromate free conversion coating, without which adhesion and blister resistance suffer.
Surface treatment. Both coatings are normally supplied passivated, oiled, or passivated and oiled, to prevent white rust in transit and to control friction in the press.
Corrosion Performance and Service Life
GI protects steel in two ways at once. The zinc layer is a barrier, and because zinc is less noble than steel it also protects exposed cut edges and scratches cathodically, so a small damaged area does not become the start of a rust stain. That combination is why galvanized sheet is the default choice for unpainted building products such as roofing, cladding, purlins, ducting and general fabrication.
GA still contains zinc, but most of it is bound as alloy, so sacrificial action at a cut edge is much weaker. The grade earns its place where the part is painted and the paint film, not the coating, is the corrosion barrier; unpainted GA performs less well than GI of a comparable coating mass, and cut edges in a wet environment should be protected or the design changed.
Aluminium-zinc coatings behave differently again. The aluminium rich oxide layer is very stable in most atmospheres, and the atmospheric life of an aluminium-zinc coating is commonly quoted as roughly two to four times that of an equal coating mass of zinc in rural and industrial exposures, which makes it popular for roofing, wall cladding, cooling towers and agricultural buildings. The advantage narrows in strong chloride environments and at cut edges, where the coating cannot protect the exposed steel cathodically, so detail design and edge treatment decide whether the service life expectation is actually met.
Selection Guide and Verification
| Application | Usual choice | Reason |
|---|---|---|
| Roofing, cladding, purlins, ducting | GI, heavier coating mass | Unpainted service, cut edges protected sacrificially |
| Painted automotive and appliance panels | GA | Paint adhesion, weldability, consistent matt surface |
| Long life cladding and agricultural buildings | Aluminium-zinc AZ | Long atmospheric life, good heat reflectivity |
| General fabrication and enclosures | GI | Lowest cost per protected square metre, easy forming |
| Coastal or high chloride site | Heavier coating mass, coating type confirmed by exposure test | Coating life scales with mass; chloride shortens it sharply |
Whatever the coating, verify it on the mill certificate rather than from appearance alone: coating type, coating mass per side and in total, surface treatment, spangle condition and mechanical properties should all be stated. On site, adhesion can be checked with a bend, cup or tape test on a sample from the delivered coil, and the coating mass can be confirmed by a stripping test where the specification is critical. Matching the coating to the environment, the finishing route and the design life is the whole decision; cost per tonne is a poor guide on its own, because a lighter coating that fails early is the most expensive option of all.
FAQ
Q: What is the main difference between GA and GI?
GI carries an essentially pure zinc coating straight from the molten zinc bath, while GA has been reheated after the bath so that iron diffuses into the coating and turns it into a zinc-iron alloy with a matt grey surface.
Q: Which coating is better for painting?
GA is normally the better painting substrate because its matt alloy surface takes paint directly, whereas GI needs a conversion coating pretreatment before painting to achieve reliable adhesion and corrosion performance.
Q: Is GA or GI better for welding?
GA generally welds more consistently in resistance spot welding, with longer electrode life, while GI needs higher welding currents and more frequent electrode maintenance because of the low resistance zinc surface.
Q: Does GA have the same corrosion life as GI?
No. GA gives up sacrificial protection at cut edges, so unpainted GA has a shorter corrosion life than GI of a similar coating mass; GA is chosen where the part is painted and the paint film provides the barrier.
Q: What is an aluminium-zinc or galvalume coating?
It is a hot dip coating of about 55% aluminium, 43.4% zinc and a small silicon addition, usually designated AZ in EN 10346, offering a long atmospheric life in rural and industrial environments but limited protection at cut edges.
Q: How is the coating specified on an order?
By coating type plus coating mass, for example a pure zinc coating of a stated total mass or a zinc-iron coating of a stated mass per side, together with the surface finish, passivation and oiling condition, and the values are checked on the mill certificate.


