Home-Knowledge-

Content

What Is Pickled and Oiled Steel Coil? EN 10051 Process and Uses

May 29, 2024

What Pickled and Oiled Steel Coil Is

Pickled and oiled coil is hot-rolled coil whose surface oxide has been removed by acid pickling and whose surface has then been protected with a thin film of oil. The result is a clean, light grey, uniformly matte surface that sits between ordinary hot-rolled and cold-rolled product in both price and finish. Because descaling removes mill scale, the material can be painted, welded, cold formed or laser cut without the aggressive surface preparation that black hot-rolled coil demands.

The grade and dimensional range stay those of the parent hot-rolled coil. EN 10051 governs the tolerances for continuously hot-rolled uncoated flat products, and GB/T 3274 covers hot-rolled plates and strips of carbon structural steel. Grades such as S235JR, S355JR, Q235B and Q355B to EN 10025-2 and GB/T 1591 are regularly supplied in the pickled and oiled condition.

The Pickling Line Process

Uncoiling: the hot-rolled coil is opened and fed into the line under controlled tension.

Straightening and levelling: residual coil set, crossbow and warp are removed before processing.

Pickling: the strip passes through hydrochloric acid baths that dissolve the iron oxide scale.

Rinsing: residual acid and iron salts are washed off by cascaded water sprays.

Edge trimming: the irregular edge produced by hot rolling is sheared to a uniform width.

Oiling and recoiling: a controlled oil film is applied and the strip is recoiled under tension.

Hydrochloric acid pickling has largely replaced sulphuric acid on modern lines because the spent liquor can be regenerated and because the resulting surface is more uniform and less prone to over-pickling.

Surface Condition and Tolerances: EN 10163 and EN 10051

Because pickling removes scale, the visible surface is judged against EN 10163, which grades the permitted amount of surface imperfection. Class A1 permits the widest range of marks and class A3 is the most demanding, so visible parts are normally ordered to class A2 or A3 while hidden structural parts are accepted to class A1. Thickness, width, flatness and camber for the pickled product are ordered to EN 10051, the same tolerance standard that applies to the parent hot-rolled coil.

Buyers should state clearly whether a light oil film is required, whether the oil must be removable by alkaline cleaning before painting, and whether the coil must be supplied dry for a subsequent galvanizing or coating line. Oil type and film weight affect both corrosion protection in transit and paint adhesion at the customer plant.

Mechanical Properties and Formability

Pickling does not change the mechanical properties of the base steel, so yield strength, tensile strength and elongation remain those of the ordered grade. What changes is the behaviour on the shop floor: a scale-free surface gives longer tool life, lower friction in dies and a smoother result after bending and roll forming. The 0.5 mm to 8 mm thickness band, where scale removal saves most cost while tight tolerances are still achievable without cold rolling, is the usual application window.

Property Effect of pickling and oiling
Yield and tensile strength Unchanged from the ordered hot-rolled grade
Elongation and toughness Unchanged
Surface friction in dies Lower, so forming loads are reduced
Paint and weld preparation Simple cleaning is enough, no grit blasting needed

Storage, Handling and Typical Applications

The oil film protects the surface for many months when coils are stored indoors on dry dunnage, but condensation during sea transport can cause white rust or staining. Export coils are therefore wrapped with VCI paper and plastic film, and the inner and outer wraps are sealed. Typical uses include automotive brackets and reinforcements, shelving and racking, furniture frames, compressor and motor housings, container components, cable trays, light structural sections and general fabrication where a clean surface matters but full cold-rolled appearance does not.

Frequently Asked Questions

Q: Is pickled and oiled coil the same as cold-rolled coil?

A: No. It is hot-rolled coil with the scale removed. It offers a cleaner surface than black hot-rolled coil at a lower cost than cold-rolled coil, but dimensional accuracy and surface smoothness are not equivalent.

Q: Why is oil applied after pickling?

A: The freshly pickled surface is chemically active and rusts quickly. A thin oil film provides temporary protection during storage and transport and is easily removed before painting or welding.

Q: Which standard covers the surface condition of pickled coil?

A: EN 10163 covers delivery requirements for the surface condition of hot-rolled flat products, with classes from A1 to A3 for weldable unalloyed steel.

Q: Can pickled and oiled coil be laser cut directly?

A: Yes, provided the surface is clean and dry. The oil film should be light and uniform, and some fabricators wipe or degrease the sheet before cutting to avoid smoke and spatter.

Q: Which thickness range is normally supplied?

A: Coils from about 0.5 mm to 8 mm are common, with widths typically up to 1500 mm and edge condition ordered as mill edge or trimmed edge.

Q: How should pickled coils be stored?

A: Store indoors on dry dunnage with the coil axis horizontal, keep the wrap intact, and avoid rapid temperature changes that cause condensation on the steel surface.

SEND INQUIRY

SEND INQUIRY