Home-Knowledge-

Content

What Is Cold Rolled Steel? Process, Grades & Uses

Dec 04, 2025

1. What Is Cold Rolling?

Cold rolling is a metalworking process in which hot-rolled pickled steel is further reduced in thickness at, or slightly below, room temperature by passing it between heavy rolls. Because the steel is not re-heated, the process work-hardens the material, refines the surface, and allows very precise gauge control. The result is a cold rolled plate or sheet with a smooth, bright surface, tighter dimensional tolerances, and improved mechanical consistency compared with hot rolled material of the same nominal thickness. This is why cold rolled steel is the default substrate for automotive panels, appliances, office furniture, and any product where appearance and precision matter.

2. Cold Rolled vs. Hot Rolled: Key Differences

Factor Hot Rolled Cold Rolled
Processing temperature Above recrystallization temperature At or near room temperature
Surface finish Rougher, with scale Smooth, bright, scale-free
Dimensional tolerance Wider Tighter, more uniform gauge
Strength Base level Increased by work hardening (temper-dependent)
Typical cost Lower Higher (extra processing)
Typical use Structures, frames, heavy fabrication Panels, enclosures, appliances, automotive skin

3. Main Families of Cold Rolled Steel

Carbon steels (forming grades): governed by EN 10130 (DC01–DC07) or JIS G 3141 (SPCC–SPCE), these are low-carbon grades designed for stamping, bending and deep drawing. Stainless steels: iron-chromium (and nickel) alloys providing corrosion and heat resistance for food processing, chemical equipment and architecture. Alloy steels: with additions such as chromium, nickel, molybdenum or titanium for higher strength, wear resistance or toughness - used in gears, bearings and automotive components. Electrical steels: specially processed silicon steels with high magnetic permeability and high electrical resistivity to minimize eddy-current losses in motors, generators and transformers. HSLA (high-strength low-alloy) steels: combine higher strength with good weldability and formability for lighter-weight structures. Press-hardening steels: cold rolled grades designed for hot stamping of automotive body parts, delivering very high final strength after the press-hardening cycle.

4. Typical Applications

Automotive: body panels, structural reinforcements, seat components. Appliances: refrigerator and washing-machine housings, internal liners. Construction: profiled sheets, purlins, office furniture and partition frames. General manufacturing: enclosures, cable trays, drawn housings, and precision sheet-metal parts. Where corrosion resistance is also required, cold rolled steel is often supplied as the substrate for hot-dip galvanizing (e.g., SGCC per JIS G 3302 or DX51D per EN 10346).

5. How to Specify Cold Rolled Steel

In your inquiry, define: governing standard (e.g., EN 10130, JIS G 3141, ASTM A1008), grade (e.g., DC01 or SPCC), thickness and width with tolerances, temper (skin-pass category, e.g., CQ/DQ/DDQ for drawing quality), surface finish (e.g., bright, matte), edge condition (mill edge or slit edge), and form (coil, sheet, strip). For forming-critical parts, also state the required r-value and n-value, and request the mill test certificate.

Frequently Asked Questions

What is the difference between cold rolled plate and hot rolled plate? Cold rolling is done at or near room temperature and produces a smoother surface, tighter tolerances and higher strength through work hardening. Hot rolling is done above recrystallization temperature, costs less, and is preferred where surface finish is secondary.

Is cold rolled steel stronger than hot rolled steel? In the same grade, yes - cold rolling work-hardens the material, so yield and tensile strength are typically higher. However, strength also depends on grade and temper; a high-strength hot rolled grade can still exceed a soft cold rolled grade.

What grades are used for deep drawing? In EN 10130, DC04–DC07 offer increasing deep-drawing capability; in JIS G 3141, SPCD–SPCE are the corresponding drawing grades. These have controlled r- and n-values for stretchability and drawability.

Can cold rolled steel be galvanized? Yes - most hot-dip galvanized products (e.g., SGCC per JIS G 3302, DX51D per EN 10346) use a cold rolled substrate. Specify the galvanizing standard, coating mass, and surface treatment separately from the base steel.

What is temper / skin pass in cold rolled steel? Skin pass (temper rolling) is a light final reduction that controls surface roughness, flatness and yield-point behaviour. It also determines the forming category - commercial quality (CQ), drawing quality (DQ) or deep drawing quality (DDQ) - which must match your stamping process.

Does the page's claim that electrical steel has low permeability make sense? No - electrical steel is engineered for high permeability and high resistivity. Low permeability would defeat its purpose in transformers and motors. The original page statement was a technical error and has been corrected in this rewrite.

SEND INQUIRY

SEND INQUIRY