Why the Substrate Matters
A galvanized steel sheet is two things at once: a zinc coating that manages corrosion and a steel substrate that carries the mechanical load and survives the forming operation. The coating decides how long the sheet lasts outdoors; the substrate decides whether a part bends, rolls, or deep draws without splitting. Ordering galvanized sheet by coating only, or by a brand name, leaves the substrate unstated, which is why international standards encode the substrate in the grade name.
Reading the Grade Name
Two naming systems cover most of the galvanized sheet traded internationally. Under EN 10346, the DX series is read as follows: D means flat products for cold forming, X means the substrate may be hot-rolled or cold-rolled at the mill's choice, the two-digit number marks the formability step, and the final D means continuously hot-dip coated. The coating type is added as a suffix, Z for zinc, ZA for zinc-aluminium, and AZ for zinc-aluminium-magnesium or aluminium-zinc alloy. Under JIS G3302, the SG series is read as S for steel, G for galvanized, and a final letter for quality: C for commercial, D for drawing, with numbers 1, 2, and 3 marking deeper drawing capability.
The Most Common Substrate Grades
| Grade | Standard | Substrate meaning | Typical use |
|---|---|---|---|
| DX51D + Z | EN 10346 | Commercial grade for bending and profiling | Roofing, cladding, corrugated sheets, cable trays |
| DX52D + Z | EN 10346 | Drawing grade | Pressed panels, drawn enclosures |
| DX53D + Z | EN 10346 | Deep-drawing grade | Appliance housings, drawn shells |
| DC51D + Z | EN 10346 | Cold-rolled substrate guaranteed | Surface-critical and consistent-forming parts |
| SGCC | JIS G3302 | Commercial quality | General sheet work, roofing, ducting |
| SGCD1 / SGCD2 / SGCD3 | JIS G3302 | Drawing / deep drawing / extra deep drawing | Pressed and drawn parts |
| S220GD to S550GD | EN 10346 | Structural grades, minimum yield strength in MPa | Purlins, framing, load-bearing profiles |
| Q235B base | GB/T 700 | Carbon structural steel for building sheet | Building products, ventilating duct |
The DX51D Family in Detail
DX51D is the workhorse of the EN 10346 system. It is a low-carbon grade with good bending and roll-forming behaviour, and it covers most architectural and general fabrication needs: corrugated roofing, flashings, cable trays, ductwork, and light structural profiles. When the second letter is I in related DC designations, such as DC51D, the supplier guarantees a cold-rolled substrate, which is specified when the forming process or the painted surface depends on a consistent cold-rolled finish. DX52D and DX53D are selected as the drawing depth increases; DX53D corresponds in practice to a deep-drawing substrate equivalent to the DC04 or DC05 level of EN 10130.
Structural Grades for Load-Bearing Parts
When the galvanized sheet itself carries load, the substrate must be a structural grade. EN 10346 provides S220GD, S250GD, S280GD, S320GD, S350GD, S400GD, S450GD, S500GD, and S550GD, where the number is the minimum yield strength in MPa. S350GD is the common choice for roll-formed purlins and cladding rails in steel building systems, while S450GD and above are used for high-strength profiles where weight saving is a design goal. Structural grades have controlled yield and tensile limits and are tested to the requirements of EN 10346 before coating, so they are not interchangeable with forming grades in load calculations.
Matching Substrate to Application
Roofing and wall cladding: DX51D + Z or SGCC with a coating of 180 to 275 g/m2.
Corrugated sheets for sheds and warehouses: DX51D + Z or SGCC.
Roll-formed purlins and structural members: S350GD or S450GD with the required coating class.
Deep-drawn appliance housings: DX53D + Z or SGCD2/SGCD3.
Electronics and computer chassis: electro-galvanized SECC on a cold-rolled substrate.
Precision painted parts: DC51D + Z with a guaranteed cold-rolled substrate.
Quality and Sourcing Notes
One claim sometimes repeated in the market is that SGCC-type hot-dip material cannot be made to good quality locally and must be imported. That claim is not supported by current production reality. Continuously hot-dip galvanized sheet to JIS G3302 and EN 10346 is manufactured in large volumes by mills in China, Japan, Korea, and elsewhere, and the difference between domestic and imported supply is normally a question of cost, lead time, and coating class availability, not of whether the grade exists at all. What protects the buyer is a precise specification: standard, substrate grade, coating designation, spangle, surface finish, and the mill test certificate. When the certificate states JIS G3302 SGCC with a Z27 coating class, the material is defined well enough to be judged on its own terms regardless of origin.
Frequently Asked Questions
Q: What does DX51D+Z mean?
A: Under EN 10346, D is flat product for cold forming, X means the substrate may be hot-rolled or cold-rolled, 51 is the commercial formability step, D means continuously hot-dip coated, and Z is a zinc coating.
Q: What is the difference between DX51D and DC51D?
A: In DC51D the second letter C replaces X, which guarantees a cold-rolled substrate. DX51D allows the mill to supply either a hot-rolled or cold-rolled substrate within the same mechanical envelope.
Q: What does SGCC stand for?
A: In JIS G3302, S is steel, G is galvanized, and C is commercial quality. SGCD1, SGCD2, and SGCD3 are the drawing, deep-drawing, and extra deep-drawing steps of the same series.
Q: Which substrate is best for deep drawing?
A: DX53D + Z under EN 10346 or SGCD2/SGCD3 under JIS G3302, with the drawing severity dictating the step. The coating thickness should be kept moderate on deep-drawn parts to avoid coating cracking.
Q: Is SGCC material available from Chinese mills?
A: Yes. Continuously hot-dip galvanized sheet to JIS G3302 is produced in large volumes in China and other countries; the relevant factor is whether the mill certificate confirms the grade and coating class, not the origin.
Q: What are the S-series grades such as S350GD used for?
A: They are structural substrates whose number is the minimum yield strength in MPa. S350GD is common for roll-formed purlins and framing, and S450GD and above for high-strength profiles where weight is critical.
Q: How do I order galvanized sheet without ambiguity?
A: State the standard, the substrate grade, the coating designation, spangle, surface finish, thickness and width, and require a mill test certificate that matches the order.


