Home-Knowledge-

Content

Cold-Rolled Steel Grades for Mold and Die Design: SPCC, SPCD, SPCE, SPCF and SPCG

Sep 08, 2025

Material selection is one of the first and most important decisions in mold and die design: the grade of the sheet metal determines how far it can be drawn, how well it holds a surface finish after forming, and whether the part will crack, wrinkle or spring back during production. This article explains the JIS G 3141 cold-rolled mild steel grades - SPCC, SPCD, SPCE, SPCF, SPCG and SPCEN - and their electrolytic zinc-coated counterparts, so that designers can match the material to the severity of the forming operation.

1. Grade Classification (JIS G 3141)

 

Click to get today's price list!

 

Class Designation Characteristics Typical thickness (mm) Typical width (mm) Main applications
Commercial quality SPCC / SPCCT Suitable for bending and simple forming; the most widely used class 0.18–3.0 600–1500 Refrigerators, cabinets, distribution boards, drums
Drawing quality SPCD Drawing quality with excellent thickness uniformity 0.18–2.0 600–1250 Automotive floor and roof panels
Deep drawing quality SPCE Deep drawing quality with metallurgically controlled grain size; retains a good surface after deep drawing 0.18–2.0 600–1250 Automotive fenders and quarter panels
Extra deep drawing (non-aging) SPCF Non-aging steel for demanding deep drawing; resistance to stretcher-strain (fluting) over time 0.18–2.0 600–1250 Complex drawn automotive body parts
Super extra deep drawing SPCG Highest formability in the series for the most severe draws 0.18–2.0 600–1250 Severely drawn components with tight radii
Non-aging deep drawing SPCEN "N" suffix denotes guaranteed non-aging (strain-ageing free) performance 0.18–2.0 600–1250 Exposed auto panels requiring stable forming behaviour

Thickness and width figures are typical available ranges from the supplier; the governing standard for grade and mechanical requirements is JIS G 3141 (current edition).

 

2. How the Grades Differ in Practice

 

All of these grades are low-carbon cold-rolled steels; the difference lies in how the steel is controlled during production. Higher formability classes receive tighter control of chemistry (lower carbon and residual elements), a more refined grain structure and more consistent mechanical properties across the coil. In practice, this means:

 

  • SPCC is the workhorse grade for bending, blanking and light forming where the drawing depth is modest.
  • SPCD is specified where parts are drawn to moderate depth and uniform behaviour from coil to coil matters.
  • SPCE is used for deep-drawn parts that must keep a clean, unmarked surface - its controlled grain size is what preserves the finish after severe forming.
  • SPCF / SPCG are chosen for the most severe draws; SPCF additionally offers non-aging behaviour, avoiding stretcher-strain marks that can appear on aged sheet during deep drawing.

 

3. Electrolytic Zinc-Coated Variants (SECC, SECD, SECE)

 

Where the formed part needs a thin, uniform zinc layer on both sides - for corrosion resistance before painting, or for electrical applications such as chassis parts and brackets - electrolytic galvanized (EG) cold-rolled steel is used. These grades share the same formability ladder as the bare grades, with the "S" prefix replaced by "SE":

 

  • SECC - electrolytic zinc-coated commercial quality;
  • SECD - drawing quality;
  • SECE - deep drawing quality.

 

The governing standard for the coating and base material is JIS G 3313 (current edition). Typical coating thicknesses are in the range of 5–20 µm per side, so SEC series corrosion protection is lighter than hot-dip galvanizing - it is a processing and painting aid rather than a heavy-duty barrier.

 

4. Surface Treatment Suffixes (Fingerprint-Resistant Coatings)


For appliance and electronic chassis applications, EGL sheet is often supplied with an added anti-fingerprint organic or inorganic coating. Common industry designations use a suffix after the grade (e.g. SECC-K2):

 

K2 - organic (resin-based) coating for fingerprint resistance and better paint adhesion;
KS - inorganic (silicate-based) coating;
CS-type - a UF-treated fingerprint-resistant finish designation used in some supply chains.
Coating designation systems vary by mill and market; always confirm the exact coating type, coating weight and lubricant status with the supplier in writing before ordering.

 

5. Selection Checklist for Mold and Die Designers


Estimate the draw ratio and forming severity; select SPCC → SPCD → SPCE → SPCF/SPCG as severity increases.
If the part is exposed and appearance matters, choose SPCE or better for grain-size control.
If parts are stored between rolling and forming, specify a non-aging grade (SPCF/SPCEN) to avoid fluting.
If corrosion resistance or paintability before assembly is required, consider the SEC series (JIS G 3313).
Always confirm mechanical property limits (yield, tensile, elongation), thickness tolerance and surface finish against the governing standard and the mill certificate.

 

Popular specifications are in short supply!
click to get the specification sheet!

 

Classification Designation Characteristics Size ( mm ) Main applications
Commercial quality SPCC,SPCCT Commercial quality suitable for bending fabrication and simple forming; this is the type in greatest demand. Thickness
0.18-3.0
Width
600-1500
Refrigerators, cabinets, power distribution boards and drums.
Drawing quality SPCD Drawing quality second only to that of SPCEN. Excellent uniformity. Thickness
0.18-2.0
Width
600-1250
Automobile floor and roof panels.
Deep-drawing quality SPCE,SPCF Deep-drawing quality. With metallurgically controlled grain size, it retains its beautiful finish even after being deep-drawn. Thickness
0.18-2.0
Width
600-1250
Automobile fenders and quarter panels

 

Packaging and Shipping

 

Cold-rolled steel packaging

 

GNEE STEEL specializes in cold-rolled steel sheets, galvanized steel coils, and galvanized steel pipes, offering a wide range of specifications in compliance with international standards such as ASTM, EN, JIS, and GB. Whether serving the construction, automotive, appliance, or infrastructure sectors, we offer the right steel solutions for your needs.

 

SEND INQUIRY

SEND INQUIRY