galvanized steel plate
Looking for trusted galvanized steel plate manufacturers in China? You've come to the right place. As a direct factory with 20 years of structural steel experience, GNEE Steel supplies EN 10346 compliant sheets at factory prices. Mastering proper forming and fabrication techniques is essential to maximize the performance of S350GD+Z120 galvanized steel plate in your products.
S350GD+Z120 offers good formability while maintaining high strength, making it suitable for various fabrication processes. Proper technique ensures the zinc coating remains intact and the material retains its structural integrity.

Galvanized steel plate
Common Fabrication Processes for S350GD+Z120
S350GD+Z120 can be processed using various fabrication methods, each requiring specific parameters.
| Fabrication Process | Application | Recommended Parameters for S350GD+Z120 | Key Considerations |
|---|---|---|---|
| Cutting (Shearing) | Straight cuts for sheets/panels | Blade gap: 5-10% of material thickness; cutting speed: 10-15m/min | Use sharp blades to avoid coating damage; support material properly |
| Bending | Creating angles, channels, and profiles | Minimum bend radius: 1.5×thickness (for 90° bends); bend speed: 5-10mm/s | Avoid sharp bends that can crack the zinc coating; bend parallel to rolling direction when possible |
| Punching | Creating holes for fasteners or openings | Punch diameter: ≥1.2×thickness; punch speed: 20-30 strokes/min | Use lubricated punches to reduce coating wear; deburr holes after punching |
| Roll Forming | Producing continuous profiles (purlins, rails) | Roll speed: 15-25m/min; roll diameter: ≥20×material thickness | Gradual forming with multiple passes; ensure uniform pressure |
| Welding | Joining components (see detailed welding table below) | MIG: 180-220A, 22-26V; TIG: 80-120A, 10-14V | Remove zinc coating near welds; use proper shielding gas |
Bending Guidelines for S350GD+Z120 Galvanized Steel Plate
Bending is one of the most common fabrication processes for S350GD+Z120, requiring careful attention to avoid coating damage.
| Material Thickness (mm) | Minimum Bend Radius (mm) | Bend Angle | Recommended Tooling | Coating Protection Measures |
|---|---|---|---|---|
| 0.8 - 1.2 | 1.5×thickness | Up to 180° | Rubber-coated dies | Use plastic or rubber protectors on tooling |
| 1.5 - 2.0 | 2×thickness | Up to 135° | Precision bending dies | Apply protective film before bending |
| 2.5 - 3.0 | 2.5×thickness | Up to 90° | Heavy-duty bending dies | Avoid repeated bending in the same area |
| 3.5 - 5.0 | 3×thickness | Up to 90° | Hydraulic bending press | Pre-heat to 100-150°C for tight bends (optional) |
Welding Parameters for S350GD+Z120 Galvanized Steel Plate
Welding S350GD+Z120 requires specific parameters to ensure strong welds and minimize zinc fume emissions.
| Welding Method | Wire/Electrode Type | Current (A) | Voltage (V) | Shielding Gas | Pre-Weld Preparation |
|---|---|---|---|---|---|
| MIG/MAG | ER70S-6 (0.8-1.0mm) | 160-180 (1mm) | 20-22 (1mm) | 80%Ar+20%CO2 | Remove zinc 20mm from weld line |
| MIG/MAG | ER70S-6 (1.2mm) | 190-220 (2mm) | 23-25 (2mm) | 80%Ar+20%CO2 | Clean surface with wire brush |
| TIG | ER308L (1.0mm) | 80-100 (1mm) | 10-12 (1mm) | Pure Argon | Grind weld area to bare metal |
| TIG | ER308L (1.6mm) | 110-130 (2mm) | 12-14 (2mm) | Pure Argon | Use back purge for critical welds |
| SMAW | E6013 (3.2mm) | 80-100 (2mm) | 22-24 (2mm) | - | Remove zinc and clean with acetone |
Post-Fabrication Treatment for S350GD+Z120
Proper post-fabrication treatment protects the material and extends its service life.
| Treatment Process | Purpose | Recommended Products | Application Method |
|---|---|---|---|
| Zinc-Rich Primer | Touch up damaged coating areas | Zinc content ≥90% primer | Brush or spray application |
| Passivation | Enhance corrosion resistance | Chromate-free passivator | Dip or spray, then air dry |
| Sealing | Prevent moisture penetration | Polyurethane sealant | Caulk gun for joints and edges |
| Cleaning | Remove fabrication residues | Mild detergent solution | Wipe with soft cloth, rinse with water |
Proper forming and fabrication techniques are essential to maintain the quality and performance of S350GD+Z120 galvanized steel plate. By following the recommended parameters and best practices, you can achieve high-quality finished products with excellent durability. If you need technical support for fabricating S350GD+Z120 for your specific application, contact GNEE Steel's engineering team for customized guidance!
- Available Steel Grade
| Steel grade | Coating | Yield(MPA) | Tensile(MPA) | Elongation(%) |
| DX51D | Z,ZF | -- | 270-500 | 20 |
| DX52D | Z,ZF | 140-300 | 270-420 | 22 |
| DX53D | Z,ZF | 140-260 | 270-380 | 26 |
| DX54D | Z,ZF | 140-220 | 270-350 | 30 |
| S220GD | Z,ZF | 220 | 300 | 18 |
| S250GD | Z,ZF | 250 | 330 | 17 |
| S280GD | Z,ZF | 280 | 360 | 16 |
| S320GD | Z,ZF | 320 | 390 | 15 |
| S350GD | Z,ZF | 350 | 420 | 14 |
| S400GD | Z,ZF | 400 | 470 | -- |
| S450GD | Z,ZF | 450 | 530 | -- |
| S500GD | Z,ZF | 500 | 560 | -- |
Request mechanical properties report + SGS test certificate


