Galvanized Steel Coil

S320GD+Z hot dip galvanized plates(coils) are featured with strong coating adhesiveness, high erosion-resistance, accurately controlled zinc coating thickness, high size precision, flat profile and good mechanical, processing and welding performance. They can be used for making outside and inside automotive plates, structural parts and reinforcements.
S320GD+Z hot dip galvanized automotive steel size:
Nominal thickness: 0.30mm~3.0mm, nominal width: 800mm~1830mm
Note: nominal thickness of a plate/strip is sum of base plate thickness and coating thickness.
S320GD+Z hot dip galvanized automotive steel mechanical performances and coating adhesiveness:
| Steel grade | Mechanical performances | Coating adhesiveness | |||
| Yield strength MPa≥ | Tensile strength MPa≥ | After breakage percent elongation %≥ | Bending center diameter ( a=plate thickness) | ||
| L0=80mm, b=20mm | |||||
| Nominal thickness mm | |||||
| ≤0.7 | >0.7 | ||||
| S320GD+Z, S320GD+ZF | 320 | 390 | 15 | 17 | 3a |
a.bending center diameter is 4a in case of nominal thickness>1.5mm.
S320GD+Z hot dip galvanized automotive steel coating weight range:
Coating form |
Applicable surface structure | Weight range of following coatings a g/m²(A/B) | |
| Zinc coating | Zn-Fe alloy coating | ||
| Equally coating | Z, X, G, GX, N, R | 40/40~225/225 | 30/30~90/90 |
| Differential coating b | N, R | 30~150(each side) | - |
| a. 50 g/m² coating weight is equivalent to about 7.1µm. b. max. differential coating thickness ration is 1:3. |
|||
S320GD+Z hot dip galvanized automotive steel surface treatment:
1 Chromate treatment (L) |
Chromate treatment is a treatment with an aim to prevent white rusts formed on product surfaces during transportation and storage. |
| 2 Oiling (Y) | Oiling is to prevent white rusts formed on product surfaces during transportation and storage. |
| 3 Chromate treatment + oiling (LY) | This treatment with oiling after surface chromate treatment is to further avoid the forming of white rusts. |
S320GD+Z hot dip galvanized automotive steel surface quality:
Code No. |
Features |
| FB(O3) | It is allowed for the existence of small erosion spots, dark spots, strip marks, minor chromate treatment defects and small zinc particles. |
| FC(O4) | No erosion spot is allowed. However, it is allowed for the existence of light impression, scratches, zinc flow ripple marks, minor chromate treatment defects in small range, while the other side must reach FB requirements at least. |
| FD(O5) | One side of relatively good quality must further restrict on defects, namely appearance quality after painting is not affected, and the other side must FB requirements at least. |
Zinc Thickness
| Zinc Coating Grade | Zinc Coating (g/m²) | Corrosion Resistance | Typical Applications | Remarks |
| Z30 | 30 | Very low | Indoor parts, home appliance inner panels, ventilation ducts | Not suitable for outdoor use |
| Z60 | 60 |
Low |
Indoor structures, temporary facilities | Low cost |
| Z80 | 80 | Medium | Light steel structures, base metal for PPGI | Good cost performance |
| Z100 | 100 | Medium | PPGI, fencing, general construction
|
Common export grade |
| Z120 | 120 | Medium-High |
|
Longer service life |
| Z140 | 140 | Medium-High | Industrial buildings, agricultural facilities | Suitable for outdoor use |
| Z180 | 180 | High | Long-term outdoor structures, equipment housings
|
Recommended for outdoor use |
| Z200 | 200 | Very high | Humid environments, heavy structures
|
Higher cost |
| Z275 | 275 | Excellent
|
Coastal areas, solar mounting systems, high-corrosion environments | High standard |
Available Steel Grade
|
Available Steel Grade(Ensure weight and support third-party testing) |
||||
|
Steel grade |
Coating |
Yield(MPA) |
Tensile(MPA) |
Elongation(%) |
|
DX51D |
Z,ZF |
-- |
270-500 |
20 |
|
DX52D |
Z,ZF |
140-300 |
270-420 |
22 |
|
DX53D |
Z,ZF |
140-260 |
270-380 |
26 |
|
DX54D |
Z,ZF |
140-220 |
270-350 |
30 |
|
S220GD |
Z,ZF |
220 |
300 |
18 |
|
S250GD |
Z,ZF |
250 |
330 |
17 |
|
S280GD |
Z,ZF |
280 |
360 |
16 |
|
S320GD |
Z,ZF |
320 |
390 |
15 |
|
S350GD |
Z,ZF |
350 |
420 |
14 |
|
S400GD |
Z,ZF |
400 |
470 |
-- |
|
S450GD |
Z,ZF |
450 |
530 |
-- |
|
S500GD |
Z,ZF |
500 |
560 |
-- |
|
Select type Galvanized Steel based on requirements |
||||
FAQ:
Q: What standards govern the production of S320GD steel?
A: The production of S320GD steel is regulated by standards such as EN 10147, which specify the chemical composition, mechanical properties, and coating requirements to ensure consistent quality and performance.
Q: Can S320GD steel be used for welding applications?
A: Yes, S320GD steel offers good weldability, making it suitable for various welding applications in construction and manufacturing. Its low-carbon content and specific alloying elements facilitate welding processes.
Q: What is the significance of the longitudinal and coil terms in relation to S320GD steel?
A: Longitudinal refers to the orientation of the steel grain structure, which can impact its mechanical properties. Coils denote the form in which the steel is supplied, allowing for efficient transportation and processing in manufacturing.
Q: How does the base material of S320GD steel contribute to its characteristics?
A: The base material of S320GD steel, typically a low-carbon steel, balances strength and ductility. This makes it ideal for forming and shaping processes while maintaining structural integrity.
Q: What role does manganese play in S320GD steel?
A: Manganese is an essential alloying element in S320GD steel, contributing to its strength and toughness. It also aids in the steel's ability to undergo annealing processes, improving its overall mechanical properties.


