Home-Knowledge-

Content

S320GD Galvanized Steel Coil: Mechanical Properties and Applications

Jan 19, 2026

1. What Is S320GD?

S320GD is a structural grade defined in EN 10346 for continuously hot-dip coated steel strip. In the designation, S means structural steel, 320 is the minimum yield strength in megapascals, GD identifies a grade intended for structural use and cold forming, and the suffix such as +Z or +ZF states the coating type. The material number is 1.0250.

S320GD sits between general forming grades such as DX51D and the higher-strength structural grades S350GD and S550GD. Its guaranteed 320 MPa minimum yield makes it a workhorse for load-bearing sheet parts that still need to be roll formed or pressed.

2. Mechanical Properties of S320GD

Per EN 10346, the mechanical properties below are guaranteed on the steel substrate; the zinc coating adds corrosion protection but is not part of the load path.

Property Value
Minimum yield strength ReH 320 MPa
Tensile strength Rm 360-510 MPa, confirmed on the mill test certificate
Minimum elongation A80 17% for 0.50 mm < t ≤ 3.00 mm; reduced for thinner gauges as set out in EN 10346

Two practical points follow from the standard. First, elongation falls as gauge gets thinner: EN 10346 applies reductions to the minimum elongation of 2% below 0.7 mm, 4% below 0.5 mm and 7% below 0.35 mm, so a thin S320GD coil has less stretch available in the press brake or roll former. Second, tensile strength can vary within the range shown depending on processing and coating specification, which is normal for this grade and is documented on the mill certificate.

3. Chemical Composition in Practice

EN 10346 does not set mandatory composition limits for the S220GD to S550GD structural family; the producer declares the composition and must achieve the guaranteed mechanical properties. Values published by major producers for S320GD are typically at or below the following maximums.

Element C Si Mn P S Ti
Typical maximum, wt% 0.12 0.50 1.50 0.100 0.045 0.30

4. Coating Options and Coating Classes

The coating is selected with the environment in mind, not with the strength:

+Z - pure zinc, the most common choice for building products.

+ZF - zinc-iron alloy, better suited to welding and paint adhesion.

+ZA - zinc-aluminium with about 5% aluminium, longer life in some atmospheres.

+ZM - zinc-aluminium-magnesium, improved cut-edge and scratch protection.

+AZ - aluminium-zinc with about 55% aluminium, higher heat resistance and a reflective finish.

+AS - aluminium-silicon, intended for heat-resistant service.

Coating mass is expressed in g/m2 total for both sides, from Z100 to Z600. Structural building parts are usually specified in the Z140-Z350 range, with Z275 the common default for outdoor components.

5. Typical Applications

S320GD is used wherever a formed sheet part must carry load outdoors or indoors without a paint system: roofing and cladding profiles, purlins and rails, solar panel mounting brackets, light steel framing sections, storage rack components, fencing and gate parts, cable trays and agricultural machinery guards. The combination of 320 MPa yield, good formability and a corrosion-resistant coating is what suits it to these products.

6. Specification Checklist for Buying S320GD Coil

Grade and coating: state S320GD+Z, +ZF, +ZA or +ZM and the coating class, for example S320GD+Z Z275.

Gauge: S320GD coil is commonly stocked from 0.35 to 3.0 mm; most building components use 0.4-2.0 mm.

Width: typical industry stock widths run from 600 to 1500 mm, with 1000, 1219 and 1250 mm the most frequent.

Surface: surface quality A, B or C per EN 10346, spangle type, skin pass and oiling.

Delivery form: coil, slit strip or cut sheet, with coil inside diameter and maximum weight.

Documentation: a mill test certificate confirming yield, tensile, elongation and coating mass.

7. FAQ

Q1: What standard governs S320GD?

EN 10346 is the current standard for continuously hot-dip coated steel strip. The older EN 10147 has been withdrawn and replaced by EN 10346, so new material should be ordered and certified against EN 10346.

Q2: Is S320GD the same as S320GD+Z?

The grade is the same; +Z only names the coating type. A full designation such as S320GD+Z Z275 specifies both the steel and the zinc coating class.

Q3: Can S320GD be welded?

Yes. It is a low-carbon structural steel and welds with standard arc, MIG or TIG practice. Welding zinc-coated steel produces zinc fumes, so the work area must be ventilated and the weld zone re-protected afterwards.

Q4: What thickness range is available for S320GD coil?

Typical industry stock ranges from 0.35 to 3.0 mm thickness and 600 to 1500 mm width. The exact program depends on the producing line; 0.4-2.0 mm covers most building applications.

Q5: How does S320GD differ from DX51D?

DX51D is a general forming grade with no guaranteed minimum yield strength; it is chosen for shape accuracy. S320GD guarantees 320 MPa yield, so it is the right choice when the formed part carries load.

Q6: How is S320GD coated in the mill?

In a continuous hot-dip line. Strip is cleaned and annealed, passes through a molten zinc bath near 450 C, and the coating weight is set by air knives before cooling and recoiling.

SEND INQUIRY

SEND INQUIRY