Why Motor Duty Changed the Requirement
An electric vehicle traction motor differs from an industrial motor in three ways that all change the lamination specification. It operates from a high voltage inverter, so the flux contains high frequency harmonics rather than a clean sinusoidal waveform. It runs at high rotational speed, so the rotor laminations carry large centrifugal stress. And it is designed for maximum torque and power density, so weight and volume are at a premium.
Those three conditions translate into core requirements: low specific loss at elevated frequency, high magnetic induction so that a smaller core can produce the required torque, and a mechanical strength that prevents rotor lamination deformation or failure at maximum speed.
Loss at Frequency, Not Only at 50 Hz
The conventional grade tables in GB/T 2521.2 quote specific loss at 1.5 T and 50 Hz because that is the condition for line-fed machines. A traction motor supplied by a pulse width modulated inverter sees substantial flux content at several hundred hertz and above, where eddy current loss becomes the dominant component.
Eddy current loss is proportional to the square of both frequency and lamination thickness, so reducing gauge is the single most effective lever. This is why traction motors use 0.20 mm to 0.27 mm and occasionally 0.30 mm material, compared with the 0.50 mm and 0.65 mm grades typical of industrial motors, and why grade selection is based on loss measured at higher frequency, typically reported at 400 Hz for a stated induction.
| Requirement | Industrial motor practice | EV traction motor practice |
|---|---|---|
| Nominal thickness | 0.50 mm and 0.65 mm | 0.20 mm to 0.27 mm, sometimes 0.30 mm |
| Loss condition assessed | 1.5 T and 50 Hz | Higher frequency, typically reported at 400 Hz |
| Yield strength | Commercial values sufficient | Elevated values needed to resist rotor stress at high speed |
| Coating | Standard insulation | Thin, weldable or bondable coatings for stacked and bonded rotors |
| Cutting route | Punching | Punching, laser cutting or bonded stacking, each with different loss effects |
Mechanical Strength in the Rotor
Rotor laminations are the load-bearing members that hold the magnets in a permanent magnet machine. At high rotational speed the centrifugal load is carried by the lamination bridges between the magnet slots, so the yield strength of the electrical steel becomes a design variable rather than a manufacturing detail. Grades with elevated yield strength allow thinner bridges, which reduces leakage flux and improves torque per unit of magnet material.
The trade-off is that higher strength generally comes with slightly higher loss, because strengthening is achieved through alloying and processing that disturb the ideal grain structure. Motor designers therefore work to the point where the rotor survives the overspeed test with the least loss penalty, and they expect the steel supplier to declare both property sets with the same confidence.
Coating and Stacking for Traction Motors
Inter-laminar resistance must be high enough to suppress eddy currents between laminations, but the coating must also be thin, because coating thickness adds to the stack height and reduces the effective magnetic cross section.
Bonded stacks rely on the coating or an adhesive layer to hold the lamination stack together, so the coating system must be qualified for the bonding process rather than only for insulation.
Laser cutting avoids tooling wear and allows prototype iterations, but the cut edge is a heat affected zone with higher loss, and the effect grows as thickness falls.
Annealing after punching relieves cutting stress and recovers loss, but it must be compatible with the coating and with the dimensional accuracy required for the rotor stack.
Grades, Testing and Supply Points
Grades are specified under GB/T 2521.2, IEC 60404-8-4, JIS C 2552 or ASTM A677, and the order should state thickness, width, coating type, loss limit at the required test condition, and the mechanical property requirement.
Specific loss is verified on an Epstein frame to IEC 60404-2 or by single sheet test to IEC 60404-3, and yield strength by tensile test on the strip in the direction that matches the critical rotor stress.
Surface insulation resistance is checked to IEC 60404-11, and coating adhesion is checked because a coating that fails during slitting and stacking contaminates the die and shorts the stack.
Supply is by narrow slit coil sized for the die, generally in widths matched to the multi-out die layout, with thickness tolerance controlled tightly because stack height and loss both depend on it.
Documentation should include heat number, chemistry, magnetic test results and mechanical results, issued as an EN 10204 3.1 inspection certificate.
Frequently Asked Questions
Q: Why not use grain-oriented steel in a traction motor?
A: The flux in a motor stator and rotor rotates, so it sweeps across the direction in which oriented steel performs poorly. Non-oriented steel gives uniform loss in all directions and is the correct choice.
Q: How thin can traction motor laminations be?
A: Production commonly uses 0.20 mm to 0.27 mm, with 0.30 mm still used for some designs. Below that range, punching and handling become difficult and the cost rise outweighs the loss reduction for most applications.
Q: Why does the inverter matter to the steel specification?
A: The inverter output contains high frequency harmonics. Eddy current loss rises with the square of frequency, so the effective loss in service is much higher than the 50 Hz value on the grade certificate and must be assessed at higher frequency.
Q: What limits rotor speed from a materials point of view?
A: The yield strength of the rotor lamination. The bridges between magnet slots carry the centrifugal load, so a higher strength grade allows thinner bridges and higher rotational speed for the same design.
Q: Does annealing after punching always help?
A: It relieves cutting stress and recovers magnetic loss, but it adds cost, can affect flatness and dimensions, and is only permissible with coatings that tolerate the temperature, so it is applied where the loss recovery justifies the route.


