Table of contents
1. What is IF steel?
2. IF steel grade
3. Advantages of IF steel instead of aluminum-killed steel
1. What is IF steel?
IF steel, interstitial-free steel, as the name suggests, has no interstitial atoms. Interstitial atoms are atoms that exist in the lattice gaps of iron atoms. This mainly refers to carbon and nitrogen atoms. Of course, it is impossible to completely remove the above atoms in iron, but the content Very low. The metallurgical characteristics of IF steel are: 1) ultra-low carbon: 2) micro-alloying: 3) pure steel.
IF steel can finally be put into production due to the use of vacuum degassing technology to greatly reduce the carbon content. Before the 1980s, the C content of traditional IF steel was 0.005~0.01%. Modern IF steel uses bottom-blown converter smelting and improved vacuum degassing treatment, which can greatly reduce the C content. Generally, C ≤ 0.005% (even C ≤ 0.002%), N ≤ 0.003% (even N ≤ 0.002%).
How much strong carbon and nitrogen compounds are added to the steel to form the elements titanium and niobium so that the C and N atoms can be completely fixed without the existence of interstitial solid solution atoms. This is the basis of IF steel metallurgy. Taking the processing of IF steel as an example, calculated based on chemical equivalents, as long as the titanium content in the steel meets:
Ti(at.%)/(C(at.%)+N(at.%)》≥1
In order to ensure good surface quality, there are strict requirements for non-metallic inclusions in steel. Japanese companies propose that the size of non-metallic inclusions in IF steel cold-rolled plates must be less than 100 μm.
In addition, in terms of performance, IF steel has particularly good deep drawability, and each standard has clear requirements for the plastic strain ratio r and strain hardening index n.


2. IF steel grade
When it comes to the grades of IF steel, it is indeed a bit confusing. Different regions have their own grades. You may have heard of DC04 steel, which is a more commonly used deep-drawing steel and comes from the European standard EN10130 Cold-rolled low-carbon steel flat products. For cold forming, there is also DC03/05/06 in this standard. The larger the number, the better the stamping performance.
In addition, Japan's IF steel is also relatively good. The grades in Japanese standard J1S G 3141 are: SPCC, SPCD, SPCE.
Symbol: S-steel, P-plate, C-cold, fourth digit C-common, D-stamping grade (Draw), E-deep drawing grade (Elongation) ).
There are also German brands: st12, st13, st14, st15, st14-T
Symbol: ST-steel, 12-ordinary grade cold-rolled steel plate, 13-stamping grade cold-rolled steel plate, 14-deep drawing grade cold-rolled steel plate, 15-extra deep drawing grade cold-rolled steel plate, 14- T-Super cold-rolled thin steel plate. Surface quality: FC-high-grade finished surface, FB-higher-grade finished surface.
Baosteel also has its own naming method for cold rolled steel strip grades for stamping:
1. General stamping steel: BLC B - abbreviation of Baosteel; L - Low Carbon; C - generally Commercial
2. Age-resistant low-yield steel: BLD B - Baosteel (BAOSEEL) abbreviation L Low carbon (Low Carb.on): D - stamping (Drawing)
3. Non-aging extremely deep drawing steel: BUED (BUSD) B - abbreviation of Baosteel (BAOSEEL); U - Ultra (Ultra); F - Formability:
D-Drawing
4. Non-aging ultra-deep drawing steel: BSUFD B - abbreviation of Baosteel (BAOSEEL); SU - ultra-high grade (Ultra+Super); F forming Formability)
D-Drawing
*BUSD, BUFD non-aging ultra-deep drawing cold continuous rolling steel strip
3. Advantages of IF steel instead of aluminum-killed steel
Let's discuss in detail the advantages of IF steel compared with the previous generation of aluminum-killed steel:
(1) Compared with aluminum-killed steel and boiled steel, cold-rolled IF steel has a higher plastic strain ratio, better elongation and lower yield strength. The value of IF steel can reach above 2.0, while that of aluminum kill pot and boiling steel is 1.5 and 1.2 respectively.
The typical yield strength of IF steel is about 160MPa, and the tensile strength is about 300MPa.
(2) IF steel has good formability. It can be used to replace deep-drawing aluminum-killed steel, reducing or even eliminating the intermediate annealing operation process in the user's stamping process, thereby greatly saving energy, and at the same time, it can avoid the use of aluminum-killed steel in the process. Orange peeling or cracking from coarsened grains caused by grain growth during intermediate annealing.
(3) When using IF steel for deep drawing parts, the number of stampings can also be reduced, which not only reduces the cost of stamping dies, but also improves the equipment efficiency and production speed of the stamping workshop.
(4) Due to the strength and metal fluidity of IF steel, it is possible to thin the thickness of stamping parts.
(5) The superior performance of IF steel is directly reflected in reducing the scrap rate of deep-drawn products. For example, an industrial company in Wisconsin, USA, used aluminum-killed steel on its automobile chassis and cover assembly lines, and the scrap rate was 40 to 50%. After switching to IF steel, the scrap rate was eliminated. After a company in Ohio switched to IF steel for difficult-to-punch automobile parts, the scrap rate dropped from the original 30% to less than 5%, which is well within the acceptable limit.
(6) The non-yield point extension phenomenon of IF pot prevents grooves from appearing in IF steel stamping parts. The timeless nature of IF steel will not affect its deep drawing performance during storage and can increase the user's flexibility in arranging production.
(7) IF steel not only brings many benefits to steel plants, but also facilitates users. Except that vacuum degassing equipment must be used to achieve ultra-low carbon and nitrogen, the rest of the smelting and processing can be performed on conventional equipment. Annealing after cold rolling can be box annealing or continuous annealing. In addition, since there is no yield point extension during annealing of IF steel, pass rolling can be omitted, and the IF steel produced is stable under any processing conditions.


