Home-Knowledge-

Content

Zn-Al-Mg Coated Steel Coil (ZM): Properties and Grades

Oct 11, 2025

What a Zn-Al-Mg Coating Is

Hot dip Zn-Al-Mg coated steel, abbreviated ZM, is a coated flat product in which the coating is a zinc based ternary alloy containing aluminium and magnesium. Commercial coating compositions keep aluminium within a range of about 1.5 to 8 percent with a magnesium content of not less than 0.2 percent, the balance being zinc with the usual trace additions. The coating is applied on a continuous hot dip line in the same way as conventional galvanized strip, so the substrate grades, dimensional range and delivery formats are broadly the same as for pure zinc coated coil. EN 10346 provides the designation framework for ZM coatings alongside the Z, ZA and AZ coating families.

Why Magnesium Improves Corrosion Behaviour

The benefit of magnesium lies in what it does to the corrosion products. Magnesium ions encourage the formation of a dense, well organised layer of hydrozincite, Zn5(OH)8Cl2·H2O, together with other basic zinc salts, which grows over the surface of the coating and remains stable in the presence of chloride. Because that layer is electrically insulating and sparingly soluble, it suppresses the cathodic reaction that would otherwise drive zinc dissolution. The practical consequence appears at cut edges, drilled holes and scratches: instead of a steadily widening red rust zone, the protective film forms across the exposed steel and holds the damaged area stable. Published mill comparisons place the service life of a ZM coating at several times that of an equal mass of pure zinc in the same environment, with the advantage largest in chloride bearing and mildly acidic atmospheres.

Grades, Coating Mass and Mechanical Properties

Item Typical ZM coil offering
EN 10346 grades DX51D, DX52D, DX53D, S250GD, S300GD, S350GD, S450GD, S550GD with ZM coating
Coating designation ZM followed by total coating mass, for example ZM120, ZM150, ZM200, ZM275
Thickness range 0.30 mm to 4.00 mm
Width range 600 mm to 2000 mm, cut to size as required
Structural grades Guaranteed yield strength from S250GD up to S550GD, suited to cold formed profiles
Surface Regular or minimised spangle, passivated, oiled or anti-fingerprint treated

For structural profiles the grade matters as much as the coating, because ZM is frequently used for load bearing sections. Where a solar mounting rail or a purlin must carry wind and snow load, the design uses the guaranteed minimum yield strength of the structural grade together with the coating designation, both of which appear on the mill certificate.

Forming and Joining Behaviour

Friction is lower than on an equivalent galvanized surface, which reduces tool load in roll forming and reduces the amount of lubricant needed.

Bending and profiling are performed with radii similar to those used for galvanized strip of the same grade and thickness.

Resistance spot welding is practical; electrode wear follows the usual coated steel pattern, so dressing intervals should be planned from the start of the run.

The lower friction and stable coating adhesion support multi-stage forming without coating pick up on the tooling.

For painted ZM facade panels, a pre-treatment appropriate to the coating chemistry is specified so that the finish system achieves its full adhesion and durability.

Applications and Selection Notes

The heaviest demand for ZM coil is in photovoltaic mounting structures, where C and U profiles in grades such as S350GD and S420GD class steel are roll formed and installed in exposed, occasionally coastal locations. Greenhouse frames, agricultural buildings, high speed guardrails, cable trays, electrical cabinets and HVAC components follow the same logic: exposure to humidity, condensation or chloride makes the extra coating performance worthwhile. Compared with aluminium or stainless steel, ZM coated steel offers a lower material cost for equivalent stiffness, and it is easier to form and join on conventional equipment. Selection should weigh the environment first, since a ZM coating is specified in place of a heavier zinc coating rather than in addition to one.

Frequently Asked Questions

Q: Is ZM steel the same as galvanized steel?

A: Both are hot dip zinc based coatings, but ZM adds aluminium and magnesium to the bath, which changes the corrosion product chemistry and improves edge and scratch performance.

Q: What does ZM150 mean?

A: It is a coating designation in which 150 is the total coating mass in grams per square metre across both faces.

Q: Why is ZM preferred for solar mounting?

A: Mounting structures are thin, full of cut edges and often exposed to condensation or coastal air, exactly the conditions where the magnesium rich protective film performs best.

Q: Can ZM coil be welded?

A: Yes, resistance welding is routine, and arc welding is used for structural joints with the appropriate consumable and cleaning procedure.

Q: Does ZM coating affect formability?

A: Formability follows the substrate grade, and the coating itself improves tooling behaviour through lower friction and good adhesion.

SEND INQUIRY

SEND INQUIRY