Home-Knowledge-

Content

Galvalume Coil Suppliers: DX51D to DX57D Grades and AZ Coatings

Sep 29, 2025

DC51D-Z(2).pdf

Aluzinc coated steel coil, traded internationally as Galvalume, combines the load-carrying strength of steel with a hot-dip coating of aluminium and zinc. The coating is nominally 55 percent aluminium, 43.4 percent zinc and 1.6 percent silicon by weight, and it is applied on a continuous hot-dip line rather than by electroplating. Buyers working with galvalume coil suppliers usually need two things confirmed at the same time: a grade range that covers the intended forming severity, and a coating mass that suits the service environment of the finished part.

What the Aluzinc Coating Is and How It Protects Steel

Aluzinc is a continuously hot-dip coated product. Cold rolled strip is cleaned, annealed in a reducing atmosphere and passed through a molten bath whose temperature is held near 600 °C, considerably hotter than the 450 to 460 °C used for pure zinc, because the aluminium-rich alloy must wet the steel surface evenly. A thin aluminium-iron intermetallic layer forms at the interface during the dip; the silicon content keeps that layer thin and discontinuous so the coating remains ductile enough for roll forming and bending without flaking.

The coating protects the steel through two mechanisms. Aluminium provides the barrier action and tolerates sustained high surface temperature, while zinc phases supply sacrificial, cathodic protection at sheared edges and scratches. Zinc-rich corrosion products are insoluble and tend to seal small defects, which is why aluzinc normally outlasts a zinc coating of equal mass in rural, marine and most industrial atmospheres. The advantage narrows in strongly acidic or highly alkaline environments and at cut edges, where a zinc-only coating sacrifices itself more readily.

DX51D to DX57D: Reading the Grade Designations

Most European and export enquiries are written in the EN 10346 DX series, where the number describes forming severity rather than coating class. DX51D is the commercial forming grade and the most widely stocked; DX52D adds drawing capability; DX53D covers deep drawing. DX54D through DX57D are progressively more formable interstitial-free and ultra-low-carbon grades used for complex drawn components such as appliance panels and automotive-type parts. The suffix identifies the coating: a designation such as DX51D+AZ150 states that the coating is an aluminium-zinc alloy with a total coating mass of 150 g/m² shared between the two faces.

Designation Forming class Typical use
DX51D+AZ Commercial Profiled roofing and wall sheets, general fabrication
DX52D+AZ Drawing Panels and cladding with moderate draws
DX53D+AZ Deep drawing HVAC ducting, appliance casings
DX54D+AZ Deep drawing, low carbon Complex drawn covers and housings
DX55D+AZ to DX57D+AZ Extra deep drawing Severe forming where uniform elongation is critical

JIS G3321 and ASTM A792M Grade Families

Where the specification follows Japanese practice the same product is ordered to JIS G3321 as SGLCC for commercial quality, SGLCD for drawing quality, and SGL400, SGL440 and SGL570 for the structural series, in which the number is the minimum yield strength in N/mm². Under ASTM A792M the designations are CS Type A, B and C, FS Type A and B, DS for drawing steel, plus the structural grades SS230, SS255, SS275, SS340 and SS550. The EN structural series is written with the GD suffix, for example S220GD+AZ through S550GD+AZ. Because the three systems use different tensile test directions, different yield definitions and different minimum values, a coil compliant with one standard is not automatically compliant with another; the standard and grade should be named explicitly rather than covered by the generic trade name.

Coating Mass, Spangle and Surface Treatment

Coating mass is ordered as an AZ designation that states the total mass of coating on both faces of the sheet in grams per square metre. AZ100 and AZ150 are the most widely stocked classes, and AZ150 is the usual choice for exposed roofing in humid or coastal locations. Surface appearance is controlled by the cooling practice after the coating pot. Regular spangle shows the characteristic crystalline pattern and is the standard mill finish; minimised or skin-passed spangle gives a smoother, duller surface that takes paint more evenly.

Parameter Typical value
Coating designation AZ40 to AZ150 (total mass, both faces)
Spangle Regular spangle; minimised or skin-passed on request
Surface treatment Chromate passivation, chromium-free passivation, anti-fingerprint film, oiling
Thickness range 0.23 mm to 3.0 mm
Width range 900 mm to 1250 mm
Coil inner diameter 508 mm or 610 mm
Coil weight Typically 3 t to 15 t, heavier coils available on request
Coating adhesion T-bend not worse than 3T to 4T depending on thickness
Coating cleanliness Withstands 100 double rubs with MEK solvent

Passivation chemistry deserves attention during selection. Conventional chromate passivation gives good protection against humid-storage staining, while chromium-free passivation is preferred where finished goods must satisfy restricted-substance requirements. Anti-fingerprint films are applied mainly to coil that will be handled before painting, since they reduce marking and improve paint adhesion without affecting the coating mass.

Applications and Quality Control Points

Aluzinc coil is chosen for building envelopes, agricultural buildings, ducting, appliance casings, cable trays and light structural sections. Its reflective surface lowers solar heat gain on roofing, and the coating tolerates the higher temperatures reached on unventilated roofs better than plain zinc. Roofing and cladding, purlins and framing sections, HVAC ducting, refrigerator and washer housings, grain silos and storage sheds, and outdoor electrical enclosures are all routine applications.

Confirm the ordered coating mass by stripping a sample and weighing the coating gravimetrically, as set out in the general requirements of the referenced coating standard.

Check that the mill test certificate states the standard, grade, coating designation and mechanical values for the actual coil rather than a generic grade sheet.

Inspect for coating skip, dents and edge damage before uncoiling, since edge damage exposes uncoated steel that will corrode first.

Store coils under cover and raised off the ground, and keep them dry; condensation between wraps causes white or dark storage staining.

Cut with shears rather than abrasive discs where possible, and treat cut edges on exposed exterior work with a compatible zinc-rich repair coating.

Frequently Asked Questions

Q: Is Galvalume the same as galvanized steel?
No. Galvanized steel carries a zinc coating, while Galvalume and aluzinc carry an aluminium-zinc coating of roughly 55 percent aluminium and 43.4 percent zinc. The two products have different standards, different coating designations and different edge protection behaviour.

Q: Which coating mass should be used for coastal roofing?
For exposed coastal roofing, AZ150 is the usual starting point, combined with a minimised-spangle surface for painting. Very close to the shoreline, additional protection such as a prepainted coating system is normally required because chloride deposition accelerates edge corrosion.

Q: Can DX51D+AZ be welded or bent after coating?
The strip can be roll formed, bent and resistance welded, but the coating is a sacrificial and barrier layer rather than a structural one. Welded areas and bends should be treated as potential corrosion sites, and welding parameters must avoid burning away the coating over a wide zone.

Q: How should aluzinc coil be stored?
Indoors, dry and above ground level, with the coil axis horizontal on timber or rubber-faced supports. Moisture trapped between wraps is the most common cause of staining on coated coils, and it is a storage problem rather than a coating defect.

Q: Why does coating mass matter more than coating thickness?
Standards specify coating by mass per unit area because coating density and alloy composition vary. A mass measure allows consistent comparison between suppliers, whereas thickness alone can differ slightly for the same ordered coating class.

Q: Does the aluminium-zinc coating accept paint?
Yes, after appropriate surface treatment. Chromium-free passivation or anti-fingerprint film plus a suitable pretreatment and primer system gives good paint adhesion; painting unpassivated coil without pretreatment risks poor adhesion and premature peeling.

SEND INQUIRY

SEND INQUIRY