galvanized steel
DX53D galvanized steel sheet is a steel plate with a layer of zinc on the surface, which is designed to prevent corrosion on the surface of the steel plate and extend its service life. This kind of galvanized sheet has a good appearance and must not have defects that are harmful to the use of the product, such as no plating, holes, cracks and scum, excessive plating thickness, scratches, chromic acid dirt, white rust, etc.
The chemical properties of DX53D galvanized steel sheet are mainly reflected in its resistance to corrosion, which is attributed to the metallic zinc layer on its surface. In terms of physical properties, this steel plate has good coating density and weldability. In addition, when the steel plate thickness is less than or equal to 0.35mm, its minimum elongation is reduced by 7% from the value in the table.
DX53D+Z Galvanized Steel Sheet Equivalent Material
| Grade | Euronorm | China GB | Japanese JIS | US ASTM | ||
| EN 10346:2009 | GBT 2518-2008 | JIS:G3302-2005 | ASTM A653M | |||
| DX53D+Z | DX53D+Z | DX53D+Z | SGCD2 | FS TypeA FS TypeB |
||
DX53D+Z Galvanized Steel Sheet Standard Specification
| Thickness | 0.12~2.5mm | ||||||
| Width | 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm, etc | ||||||
| Length | 1000-6000 or Since the custom | ||||||
| Surface | Normal (uneven) spangle/ Skinpassed spangle/ Regular spangle / Minimized spangles | ||||||
| Finish | |||||||
| Form | Coils, Foils, Rolls, Plain coil, Shim coil, Perforated coil, Chequered coil, Strip, Flats, Blank (Circle), Ring (Flange) etc. |
||||||
DX53D+Z Galvanized Steel Sheet Metal Content
| Grade | Element | C | Si | Mn | P | S | Ti |
| DX53D+Z | Min. |
- | - | - | - | - | - |
Max. |
0.12 | 0.5 | 0.6 | 0.12 | 0.045 | 0.3 |
Tensile strength :270~380 MPa
Yield strength :140~260 MPa
Elongation :≥30%
European EN 10346 Standard Galvanized Steel
Low carbon steel for cold forming (DX51D – DX54D)
- DX51D is equivalent to Commercial Steel, curved and profiled
- DX52D is equivalent to Forming Steel
- DX53D is equivalent to Deep Drawing Steel
- DX54D is equivalent to Extra Deep Drawing Steel
Structural Steels (S220GD – S350GD)
S220GD,S250GD,S280GD,S320GD,S350GD
Use structural steel for high load-bearing capacity, with a yield strength of 220-350
Material Comparison
|
Chinese Standard |
Japan Standard |
European Standard |
|
DX51D Z/DC51D Z (CR) |
SGCC |
DX51D Z |
|
DX52D Z/DC52D Z |
SGCD1 |
DX52D With |
|
DX53D Z/DC53D Z/DX54D Z/DC54D Z |
SGCD2/SGCD3 |
DX53D Z/DX54D Z |
|
S220/250/280/320/350/550GD Z |
SGC340/400/440/490/570 |
S220/250/280/320/350GD Z |
|
DX51D Z/DD51D Z (HR) |
SGHC |
DX51D Z |
|
Standard |
Grade |
C |
Si |
Mn |
P |
S |
Ti |
|
Forcold Forming Chinese Standard |
DX51D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
DX52D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX53D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX54D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX56D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
DX57D+Z |
0.12 |
0.50 |
0.60 |
0.100 |
0.045 |
0.30 |
|
|
Forcold Forming Japanese Standard |
SGCC |
0.15 |
0.50 |
0.80 |
0.050 |
0.030 |
0.025 |
|
SGCD1 |
0.12 |
0.50 |
0.60 |
0.040 |
0.030 |
0.025 |
|
|
SGCD3 |
0.08 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
SGCD4 |
0.06 |
0.50 |
0.45 |
0.030 |
0.030 |
0.025 |
|
|
For Structure Japanese Standard |
SGC340 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.025 |
|
SGC400 |
0.25 |
0.50 |
1.70 |
0.200 |
0.035 |
0.150 |
|
|
SGC490 |
0.30 |
0.50 |
2.00 |
0.200 |
0.035 |
0.025 |
|
|
SGC510 |
0.30 |
0.50 |
2.50 |
0.200 |
0.035 |
0.025 |
|
|
For Structure AISI Standard |
S220GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
S250GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S280GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S320GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.025 |
|
|
S350GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |
|
|
S550GD+Z |
0.20 |
0.60 |
0.70 |
0.100 |
0.045 |
0.150 |
