What DX53D 1.0355 Is
DX53D is a flat steel product for cold forming that is delivered with a continuously applied hot-dip metallic coating. The designation follows the logic of EN 10346: D indicates a flat product for cold forming, X indicates the family of hot-dip coated materials, the two digits 53 rank the forming capability within the series, and the closing D marks the delivery condition. The number 1.0355 is the material number assigned under the European numbering system, so the same material is identified in drawings and certificates either by grade or by number.
The grade sits in the middle of the forming series, above the general purpose DX51D and DX52D and below the special deep-drawing grades DX54D and higher. That position makes it the standard choice where a part needs more than ordinary formability but does not justify the cost of a top forming grade. Older designation systems list the same material under names such as FeP05G.
Chemical Composition and Mechanical Properties
The chemistry is that of an alloy quality low carbon steel, with tight limits on the elements that would otherwise raise strength and reduce ductility, and with titanium available as a stabilising addition.
| Element | Maximum content |
|---|---|
| Carbon | 0.12% |
| Silicon | 0.50% |
| Manganese | 0.60% |
| Phosphorus | 0.10% |
| Sulfur | 0.045% |
| Titanium | 0.30% |
Carbon and manganese are held low because both raise strength at the expense of elongation and of the strain hardening behaviour that drawing relies on. Titanium is used to combine with interstitial carbon and nitrogen, which stabilises the material against ageing and helps maintain forming behaviour after a period in store.
Because the forming capability of the grade is guaranteed through mechanical values rather than through a chemistry band alone, the standard also fixes the mechanical property envelope for the delivery condition.
| Property | Requirement |
|---|---|
| Tensile strength, Rm | 270 to 380 MPa |
| Yield strength, Re or 0.2% proof strength | 140 to 260 MPa |
| Minimum elongation, gauge length 80 mm | 30% |
The contrast with the general purpose DX51D grade is instructive. DX51D allows a yield strength of 140 to 320 MPa and a tensile strength of 270 to 500 MPa with a minimum elongation of 22%, so DX53D narrows the property band and raises the guaranteed elongation by eight percentage points. That narrower band is what makes forming behaviour predictable in a press line, because a wider spread would mean re-setting tooling between coils.
Coating Options and Surface Condition
DX53D can be supplied with any of the continuously applied metallic coatings of the EN 10346 family, and the coating is quoted as a designation plus a coating mass. A Z coating is pure zinc, ZA adds about 5% aluminium, AZ is the aluminium rich coating, ZM is the zinc-aluminum-magnesium coating, and AS is an aluminium-silicon coating used where the part will be heated to a high temperature and scale must be avoided.
Surface quality, surface finish and coating type are quoted separately from the grade. Surface quality classes control the level of visible defects permitted on the exposed face, surface finish classes control the roughness and the degree of temper rolling, and the coating type code identifies the treatment applied over the metallic coating to improve forming, welding or paint adhesion. Because a drawn part may have one exposed and one hidden face, the order should state which face is inspected to which quality class.
Typical Applications
Automotive interior and structural parts that are drawn or stretch formed and then painted, such as brackets, panels and reinforcements.
Domestic appliance components such as housings, doors and internal panels where forming severity is moderate to high and appearance matters.
Metal furniture, shelving and rack components, where bending radii and shallow draws are combined with a painted finish.
Electrical enclosures and cable trays with formed pockets and folded geometry.
General industry parts transferred to a press after cutting to length from coil.
Forming, Welding and Ordering Practice
Tooling and draw radii should be set for a deep-drawing grade rather than for commercial quality sheet, because a sharp radius that works on a higher strength material will thin and tear DX53D at the same setting.
Lubricant selection follows the forming severity. Drawing compounds must be compatible with the coating and with the subsequent cleaning and painting sequence.
Resistance spot welding is routine on coated DX53D, with the electrode schedule set for the coating type and mass, since a heavier coating shortens electrode life.
Cut edges are not coated. Parts exposed to condensation need the edges either sealed, painted after forming, or made from a coating with stronger edge protection such as ZM.
Order by grade plus material number, coating designation and coating mass, surface quality, surface finish, thickness and tolerance class, coil or cut length, and the required certificate type. Thickness tolerances for cold-formed coated product follow EN 10131.
Certification is normally supplied as an EN 10204 3.1 inspection certificate quoting heat number, chemistry, tensile and elongation results, coating mass and the coating mass test method.
Frequently Asked Questions
Q: What is the difference between DX53D and DX51D?
A: DX53D is a deep-drawing grade with a minimum elongation of 30% and a tensile band of 270 to 380 MPa, while DX51D is a general purpose forming grade with a minimum elongation of 22% and a wider property range.
Q: What does the number 1.0355 mean?
A: It is the material number for this grade. The two identifications describe the same steel, so a certificate quoting either can be accepted as long as the coating and delivery condition match the order.
Q: Can DX53D be ordered with a ZM coating?
A: Yes. The grade and the coating are separate choices, so DX53D is quoted with any of the standard continuously applied coatings, including zinc, zinc-5% aluminium, aluminium-zinc and zinc-aluminum-magnesium.
Q: Does the coating affect formability?
A: It does. Heavier coatings and some coating types can flake or powder at tight bend radii, so coating mass and coating type are qualified by forming trials before large orders are placed.
Q: Is DX53D suitable for parts that must be welded and then painted?
A: Yes, provided the welds are cleaned of coating residue before painting, and the coating type selected is one developed for good paint adhesion after the standard pre-treatment sequence.


