Home-Knowledge-

Content

DX52D Galvanized Coil for Home Appliances: Specs & Supply

Nov 06, 2025

1. What Is DX52D Galvanized Coil?

DX52D is a hot-dip galvanized steel grade defined in EN 10346 for cold forming applications. In the designation, "DX" indicates a flat product for cold forming, "52" is the grade index, and "D" denotes continuous hot-dip coating. The product is delivered with a zinc coating (Z), zinc-iron alloy (ZF) or other coating types, in coil, sheet and strip form.

What sets DX52D apart from the workhorse DX51D is a controlled yield strength range (140-300 MPa) and a guaranteed minimum elongation of 22%. That combination lets press lines form deeper panels and more complex geometries - like the outer and inner panels of washing machines, refrigerators and air conditioners - with less springback and fewer cracks.

2. Mechanical Properties and Grade Comparison (EN 10346)

Grade Yield strength (MPa) Tensile strength (MPa) Elongation A80, min (%) Typical use
DX51D+Z ≤360 (typical, no guarantee) 270-500 ≥20 General forming, profiles
DX52D+Z 140-300 270-420 ≥22 Appliance panels, medium forming
DX53D+Z 140-260 270-380 ≥26 Deep drawing, complex parts
DX54D+Z 140-220 270-350 ≥30 Very deep drawing

Values are per EN 10346 and may vary by thickness class; always verify against the mill certificate.

3. Coating and Surface Options for Appliance Applications

For household appliances, the visible surface must stay flawless after forming, painting or powder coating. Specify these options with your order:

Coating class: Z100-Z180 is typical for appliance parts (sufficient for indoor service); heavier classes add cost without benefit indoors.

Spangle: minimized spangle (MS) or spangle-free (FS) for smooth painted surfaces; regular spangle only for hidden parts.

Passivation: chromated or chromium-free passivation protects the coil in storage; specify fingerprint-resistant treatment for panels that will be handled bare.

Surface finish: skin-passed surface improves flatness and paint appearance.

Oiling: oiled or dry, depending on your degreasing line and storage period.

If your drawing requires the highest surface smoothness and you are comparing against electro-galvanized (EGI) coil: EGI offers a thinner, smoother zinc layer (EN 10152, typically 20-100 g/m² total) and is excellent for painted interior parts, while DX52D HDGI provides stronger corrosion protection at similar formability. Choose by corrosion requirement, not habit.

4. Typical Applications

Washing machine and dryer outer and inner panels.

Refrigerator side panels and doors (as painted or powder-coated blanks).

Air-conditioner housings and heat-pump casings.

Microwave and kitchen appliance bodies.

Shelving, display racks and office equipment panels.

Beyond appliances, DX52D is also used for roll-formed sections, cable trays and general sheet-metal components where controlled strength and good forming go together.

5. Supply Range and Export Packaging

Item Typical availability
Governing standard EN 10346 (DX52D+Z); also JIS G3302 / ASTM A653 equivalents on request
Thickness 0.12 - 3.00 mm
Width 600 - 1500 mm (slitting available)
Zinc coating Z30 - Z275 g/m² (total both sides)
Surface treatment Pickling (P), passivation (C), oiling (O), lacquer sealing (L), phosphating (P), untreated (U)
Surface structure Big spangle (BS), normal spangle (NS), minimized spangle (MS), spangle-free (FS)
Hardness Full hard, medium hard, soft (as required)
Coil ID 508 mm / 610 mm
Coil weight 3 - 20 t per coil

Packaging: waterproof paper as inner packing, galvanized or coated steel sheet as outer packing with side guard plates, secured by steel straps - or per customer specification. Coils are loaded with dunnage and waterproof covers for sea transport.

Frequently Asked Questions

When should I use DX52D instead of DX51D? Use DX52D when forming severity is moderate-to-high - deeper panels, tighter radii, or parts that show cracking or springback in DX51D. Its guaranteed yield range and higher elongation make press behavior more predictable. For simple bending and profiling, DX51D is cheaper and sufficient.

Is DX52D the same as electro-galvanized coil? No. DX52D is a hot-dip galvanized grade (EN 10346). Electro-galvanized coil (EGI, EN 10152) is a different product with a thinner, smoother coating. If your order is for EGI, specify the correct standard and coating (e.g., ZE classes); mixing the two in one enquiry causes specification errors and wrong pricing.

What coating class is recommended for appliance panels? For indoor appliance parts, Z100-Z180 is a common, cost-effective range. Heavier classes (Z275+) are unnecessary indoors; lighter classes (Z40-Z80) suit internal components that are painted or protected from condensation.

Can DX52D coil be painted or powder coated? Yes - with correct pretreatment (degreasing and, if required, light conversion coating). Choose minimized or zero spangle and specify passivation to get a smooth, paint-ready surface. Ask about our PPGI line if you need pre-painted coil directly.

How is DX52D different from SGCC (JIS G3302)? SGCC is the JIS commercial-grade designation without guaranteed mechanical properties; DX52D is an EN grade with certified yield and elongation values. For appliance panels with predictable forming behavior, DX52D (or the JIS drawing-grade equivalents) is the more controlled choice.

Do you supply cut-to-length sheets and blanks? Yes - we supply coil, cut-to-length sheet, slit strip and blanks with tight dimensional control. Provide your blank size, quantity and surface requirements for a firm quotation.

SEND INQUIRY

SEND INQUIRY