Home-Knowledge-

Content

SPCC vs SPCD: Performance Differences, Properties & Selection (JIS G 3141)

Sep 08, 2025

1. Two Grades, One Standard: JIS G 3141

SPCC and SPCD are both cold rolled steel grades defined in JIS G 3141 (cold-reduced carbon steel sheet and strip). The designations share the same skeleton - S for steel, P for plate/sheet, C for cold rolled - and differ only in the final letter, which defines the quality level: C for commercial quality and D for drawing quality. In daily trade, however, the two grades are frequently quoted interchangeably, and parts specified for drawing are sometimes made from commercial grade to save cost. That substitution is the most common source of cracked pressings and rejected parts, so understanding the real performance differences matters for every buyer, stamper and inspector.

2. Mechanical Property Differences

Characteristic (JIS G 3141) SPCC (Commercial) SPCD (Drawing)
Yield strength Not specified (no ceiling) Maximum specified (e.g., about 245 MPa in thin gauges)
Tensile strength Minimum specified (typically about 270 MPa) Minimum specified (typically about 270 MPa)
Elongation Lower minimum values Higher minimum values at the same thickness
Formability Bending, light forming Drawing, deeper forming
Typical use Panels, enclosures, general fabrication Stamped housings, drawn shells, press parts

3. Forming Behavior and Surface Response

In the press shop, the differences appear as yield-point behavior and stretchability. SPCC can show Lüders lines (stretcher strains) during forming and has no guaranteed softness, so deep draws may split at corners or show uneven springback. SPCD is produced with cleaner steel chemistry and controlled processing to suppress yield-point elongation, giving smoother plastic flow, more uniform wall thickness in drawn parts, and more predictable springback for tool setting. The drawing quality of SPCD also reduces die wear and lubricant consumption in high-volume stamping. For parts that will be painted, the more uniform surface of SPCD after forming also produces a cleaner painted appearance.

4. Applications: Which Grade for Which Part

SPCC is the economical default for parts that are cut, bent, rolled or lightly formed: office furniture panels, electrical enclosures, brackets, ducting, shelves and general fabrication. SPCD is specified when the part is actually drawn: washing machine and dryer shells, stamped appliance housings, drawn cookware, automotive inner panels, lamp housings and similar components with concave shapes that stretch the material beyond its yield point. The cost difference per tonne is small relative to the cost of a scrapped die or a cracked part, so the rule is simple: if the drawing is deeper than a shallow dish, specify SPCD or higher and confirm the mill certificate.

5. Equivalents and How to Specify

In the European EN 10130 system, SPCC behavior corresponds broadly to DC01 and SPCD to DC03; in the Chinese GB/T 5213 system the equivalents are DC01 and DC03; and in ASTM A1008 the comparison is CS (commercial steel) and DS (drawing steel). These are functional equivalents, not automatic substitutes - each standard has its own tolerances and testing rules. When ordering, write the full specification: standard (e.g., JIS G 3141), grade (SPCC or SPCD), thickness and tolerance, width, surface finish (bright or matte), oiling, and the required test documents. Request the mill test certificate showing yield strength, tensile strength and elongation, and check the values against the grade table - a certificate with no yield value on a claimed SPCD coil is a warning sign.

6. Testing and Acceptance Tips

For incoming inspection, confirm the grade by testing: a tensile test gives yield strength, tensile strength and elongation; a bend test (180° flat bend) checks ductility; and a hardness check is a quick screening method. Verify the coil label and edge markings against the certificate, and keep a sample from each delivery for traceability. For critical forming applications, run a trial stamping of the actual tool before mass production - the trial reveals split, springback and surface issues that paperwork cannot. If SPCD was ordered and the delivered coil fails the yield-strength ceiling, reject the lot and request replacement from the supplier rather than accepting a "similar" commercial grade.

Frequently Asked Questions

Q: What is the main difference between SPCC and SPCD?
A: SPCD is a drawing quality with a guaranteed maximum yield strength and higher elongation, so it draws into deep shapes without splitting; SPCC is commercial quality with no yield ceiling, suited to bending and light forming.

Q: Can I use SPCC instead of SPCD to save cost?
A: For shallow bending, yes; for deep drawing, no. The small grade premium is far cheaper than scrapped parts, damaged dies and delivery delays.

Q: What are the equivalents of SPCD?
A: Broadly DC03 under EN 10130 and GB/T 5213, and DS under ASTM A1008. Equivalents are functional, not identical, so always buy to the standard named in your contract.

Q: How do I verify that a coil is really SPCD?
A: Request the mill test certificate and check the yield strength and elongation against the JIS G 3141 grade table; a tensile test or third-party inspection can verify the values before shipment.

Q: Why does my SPCC part show surface lines after forming?
A: That is yield-point elongation (Luders banding), typical of commercial quality steel under straining. SPCD and higher drawing grades are processed to suppress this effect.

Q: Is SPCD needed for a washing machine outer shell?
A: Yes. The wrapper of a washing machine is a deep draw with visible surfaces, so SPCD (or DC03/DC04) is the typical specification, and the material must also be free from stretcher strains for a clean painted finish.

SEND INQUIRY

SEND INQUIRY