Home-Knowledge-

Content

DC01 Cold Rolled Steel Coil: A Reliable Choice for Mass Production in Southeast Asia

Mar 12, 2026

What DC01 Is

DC01 is a cold-rolled low-carbon steel grade defined in EN 10130 for flat products intended for cold forming. The DC prefix stands for steel for cold forming, and the number 01 marks the first, general-purpose step of the series that continues through DC03, DC04, DC05, and DC06 with increasing formability. The production route starts with hot-rolled strip that is pickled, cold reduced to the ordered thickness, annealed, and skin-passed. The low carbon content keeps the steel soft and ductile, while the controlled cold reduction gives a smooth surface and accurate thickness, which is what makes DC01 comfortable to run on automated stamping and bending lines.

Chemical Composition

EN 10130 sets maximum limits for the main elements of DC01. The values below are the standard limits from the standard itself; mills frequently certify tighter internal limits, which is acceptable as long as they stay within the standard.

Element (max, %) DC01 per EN 10130
Carbon 0.12
Manganese 0.60
Phosphorus 0.045
Sulfur 0.045

Mechanical Properties

EN 10130 specifies the mechanical window of DC01. The values depend slightly on thickness, and the mill certificate reports the measured results for the delivered lot.

Property DC01 per EN 10130
Yield strength 130 to 260 MPa
Tensile strength 270 to 410 MPa
Elongation A80 28% minimum above 0.7 mm; 26% for 0.5 to 0.7 mm
Surface FB normal finished surface, oiled or dry

The wide yield band and the tensile ceiling define DC01 as a forming grade rather than a structural grade: it bends, stamps, and welds easily, and the predictable elongation keeps rejection rates low in high-volume pressing. Because the elongation minimum applies to the standard gauge length of 80 mm, always compare test values against the same specimen convention when checking a certificate.

Why Manufacturers in Southeast Asia Choose It

Electronics enclosures, appliance shells, brackets, and light structural parts in Vietnam, Thailand, and Indonesia are overwhelmingly stamped from DC01. The reasons are practical. The grade runs on local press shops without special lubrication or tool changes. The surface accepts painting, plating, and galvanizing after forming. And because DC01 is produced and stocked in large volumes, lead times and prices are more stable than for specialty grades. The main quality-sensitive points in the region are thickness consistency across the coil width, flatness after slitting, and rust prevention during the humid monsoon season, all of which are controlled by specifying the standard, the tolerance class, and the packaging.

Tolerances and Acceptance

Dimensional tolerances for cold-rolled coil follow EN 10131, which defines normal and special classes for thickness, width, and flatness. As a reference, the normal thickness tolerance for a 1.0 mm coil at 1250 mm width is on the order of plus or minus 0.08 mm, and the special class is tighter. When a stamping die is sensitive to thickness, order the special class and state it on the purchase order. Acceptance is based on the mill test certificate, issued to EN 10204 type 3.1, which must state the standard, grade, dimensions, heat number, and the measured yield, tensile, and elongation values. A receiving check of thickness, width, and surface at the slitter or press is standard practice.

Surface and Storage for Tropical Climates

Cold-rolled surface is susceptible to humidity, so the standard delivery is lightly oiled and wrapped with moisture-barrier paper. In tropical conditions, storage rules matter more than the mill packaging. Keep coils indoors, off the floor on wooden supports, with the inner diameter horizontal so water cannot pool inside the coil eye. Keep the wrapper intact until the coil is used, and re-wrap partial coils. During sea freight, use containers with desiccant, avoid condensation cycles by keeping the container closed, and specify VCI paper or a heavier rust-preventive oil when the voyage crosses the equator or the port is humid. If surface stains appear, they are almost always a storage or transport issue, and a supplier who controls packaging and container loading will visibly reduce this risk.

Ordering Checklist

Standard and grade: EN 10130 DC01.

Thickness and width, with the tolerance class per EN 10131.

Surface finish and oiling: FB surface, oiled or dry.

Coil weight, inner diameter, and whether slitting or cut-to-length is needed.

Packaging for sea transport: moisture barrier, desiccant, VCI, and container loading instruction.

Documentation: EN 10204 type 3.1 mill test certificate with measured mechanical values.

Frequently Asked Questions

Q: What is DC01 steel?

A: DC01 is a cold-rolled low-carbon steel grade for cold forming, defined in EN 10130, with a yield strength of 130 to 260 MPa, a tensile strength of 270 to 410 MPa, and good bending, stamping, and welding behaviour.

Q: What is the difference between DC01 and SPCC?

A: They are equivalent general-purpose grades from two standard systems, DC01 from EN 10130 and SPCC from JIS G3141. Composition limits and testing conventions differ slightly, so the certificate must state the governing standard.

Q: Can DC01 be used for deep drawing?

A: For simple drawing only. Severe deep drawing should use DC03, DC04, or DC05, which have lower carbon, better elongation, and guaranteed r-values and n-values.

Q: What thickness tolerance can I expect?

A: Under EN 10131 the normal tolerance for a 1.0 mm coil at 1250 mm width is on the order of plus or minus 0.08 mm; the special class is tighter and should be specified when dies are thickness-sensitive.

Q: How is DC01 quality verified on delivery?

A: The mill test certificate per EN 10204 type 3.1 reports the standard, grade, dimensions, heat number, and measured mechanical values; receiving inspection checks thickness, width, surface, and coating of the rust-preventive oil.

Q: Why does DC01 arrive oiled?

A: Cold-rolled surface rusts quickly in humid air, so the coil is delivered with a light rust-preventive oil and moisture-barrier wrapping; degreasing is done before painting or plating.

Q: How should DC01 coils be stored in a tropical climate?

A: Indoors, off the floor, with the coil eye horizontal, wrappers intact, and desiccant inside any opened packaging; partial coils must be re-wrapped immediately.

SEND INQUIRY

SEND INQUIRY