How Cold-Rolled Steel Plate Is Made
Cold-rolled steel plate starts as hot-rolled pickled strip. The strip is rolled at ambient temperature through tandem or reversing cold mills, which reduces thickness and improves the surface by closing micro-defects left by hot rolling. The material is then annealed to restore ductility and skin-passed or temper-rolled to control surface finish and yield-point behaviour. Because the process is carried out below the recrystallisation temperature, cold-rolled plate offers tighter thickness tolerance, a smoother surface, and more consistent mechanical properties than hot-rolled plate of the same grade. Tolerances are governed by standards such as EN 10131 for cold-rolled uncoated products and GB/T 708 for Chinese domestic supply.
Classification by Thickness
In international trading practice, cold-rolled steel is grouped by nominal thickness into thin, medium, and thick ranges, although the boundaries vary by country and by standard.
| Category | Typical thickness | Main applications |
|---|---|---|
| Thin sheet | 0.30 – 3.00 mm | Automotive body panels, appliance casings, office furniture, stamping blanks, roofing substrates |
| Medium plate | 3.00 – 20.00 mm | Structural fabrications, machine frames, bridges and general engineering |
| Thick plate | Over 20 mm | Heavy machinery, shipbuilding, pressure parts |
Most cold-rolled coil and sheet falls into the thin range because cold rolling becomes less economical above about 3 mm; thicker products are normally hot rolled. For cold-rolled supply, the common commercial range is 0.30–3.00 mm, with 0.5–2.5 mm being the most frequently ordered band.
Classification by Steel Grade
Grade classification reflects the intended forming severity, not the strength alone. The three families most used in world trade are the European EN 10130 DC series, the Japanese JIS G3141 SP series, and the older German DIN 1623 St designations.
| EN 10130 | JIS G3141 | DIN 1623 (legacy) | Intended use |
|---|---|---|---|
| DC01 | SPCC | St12 | General forming and simple bending |
| DC03 | SPCD | St13 | Moderate drawing |
| DC04 | SPCE | St14 | Deep drawing |
| DC05 | SPCEN | St15 | Severe deep drawing |
| DC06 | SPCEN (IF) | St16 | Extra-deep drawing, interstitial-free steel |
Grade selection is driven by the most severe forming operation in the part. A component that only needs bending can use DC01 or SPCC; a drawn housing or a panel with complex geometry normally requires DC04/SPCE or higher. The mechanical property tables in EN 10130 and JIS G3141 define the proof strength, tensile strength, and minimum elongation for each grade, and these values change with sheet thickness, so the grade alone does not fix the properties.
Classification by Surface Condition
Cold-rolled plate is also classified by surface texture and by the final treatment applied on the temper mill. Surface texture is described as bright or matte; matte finishes improve paint adhesion and are preferred for visible panels. Surface treatment classes include oiled and dry: oiling gives short-term protection against white rust during storage and shipment, while dry product is used when downstream processing requires a clean surface.
Many buyers then add a metallic coating to the cold-rolled substrate. Common coated products are hot-dip galvanized steel (Z per EN 10346, or SGCC per JIS G3302), aluminium-zinc coated steel (AZ, 55% Al-Zn per EN 10346), and electro-galvanized steel (ZE per EN 10152). Each coating family has its own designation system and its own corrosion performance, and the coated product is normally specified by the base grade plus the coating mass, for example DX51D+Z275.
Classification by Delivery Form
Cold-rolled products are supplied as coil, slit coil, sheets, and cut-to-length plate. Coil is the lowest-cost form and the starting point for stamping and roll-forming lines. Sheets and cut lengths are used where the buyer has no decoiling equipment or where parts are processed in small batches. For each form, the buyer should confirm the thickness tolerance class, flatness requirements, and edge condition, because these are the parameters that most affect downstream yield.
How to Specify Cold-Rolled Plate in an Order
A complete specification contains the standard and edition, the grade, the thickness and width with tolerances, the surface condition, the delivery form, the required mechanical properties where the application is structural, and the documentation (typically a mill test certificate to EN 10204 3.1). For coated material, add the coating mass and surface finish. A precise specification avoids mismatched supply and makes it possible for different mills to offer the same product.
Frequently Asked Questions
Q: What is the difference between cold-rolled and hot-rolled steel plate?
Cold-rolled plate is hot-rolled strip that is pickled and further rolled at ambient temperature, then annealed and skin-passed. The result is tighter thickness tolerance, a smoother defect-free surface, and better consistency, at a higher price. Hot-rolled plate is thicker, cheaper, and has a mill scale surface.
Q: Is SPCC the same as DC01?
They are close equivalents from different standard systems: SPCC is the general-purpose grade of JIS G3141 and DC01 is the general-forming grade of EN 10130. Mechanical property limits differ slightly, so for a contractual application the governing standard and edition should be stated explicitly.
Q: Which cold-rolled grade is best for deep drawing?
For deep drawing use DC04 (SPCE), DC05 (SPCEN), or DC06 depending on severity. DC06, an interstitial-free grade, gives the highest r-value and elongation and is used for the most demanding draws.
Q: What surface finishes are available on cold-rolled plate?
The standard surface textures are bright and matte. Matte (rough) surfaces are specified when the part will be painted or when a controlled friction is needed in forming. The delivery can be oiled or dry, and for coated products the finish is described by the coating designation such as Z or AZ.
Q: What thickness range can be supplied as cold-rolled plate?
The commercial cold-rolled range is about 0.30 to 3.00 mm in coil and sheet form. Thicker plates are normally hot rolled because cold rolling of thick material is not economical.
Q: How is the theoretical weight of cold-rolled plate calculated?
The standard formula is weight in kg = thickness in mm x width in m x length in m x 7.85, using a density of 7.85 g/cm3 for carbon steel. The actual weight is verified against the mill certificate and shipping weights.


